>Click<

View our trade items

 

Used Pumps

Popular Manufacturers:Sykes | SPP | Selwood | Godwin | Tsurumi | Custom Build Pumps

All of our used pumps are fully tested/ serviced to be in good working order and if necessary repainted to our standard red finish (other colour options available at extra cost).

3 month warranty is given for used pumps sold within England, Wales and Scotland
excluding the following postcodes: FK, KY, PA, PH, DD and the Highlands.
Please contact us for further details.

Please note that pump photographs on this page are for general guidance only and may not depict the actual pump offered.

Pipework / Hose / Couplings available at extra cost.

All prices are excluding carriage and VAT.
Bespoke Pumps for sale

 

Bespoke pumps made and sold

6" Liquidator

New Reduced Price
£5,300

GSP-340 6inch Pumps powered by a water cooled Isuzu 3 cylinder electric start engine, all mounted in a sound attenuated canopy.
x1 remaining: (SP6355)

Flow: 5,500 litres per minute
Head: 29m

6Liquidator_1_.jpg 6Liquidator_2_.jpg 6Liquidator_3_.jpg 6Liquidator_4_.jpg 6Liquidator_5_.jpg 6Liquidator_6_.jpg 6Liquidator_7_.jpg 6Liquidator_8_.jpg 6Liquidator_9_.jpg

Apex TD40-315 Pump

£550

Apex TD40-315, B/S end suction pump. Capable of handling clean water, seawater, solvents, chemicals and other liquids with similar properties. Electric motor available

Specification
Max Pressure: 12 Bar

Apex_TD_40-315-1.jpg Apex_TD_40-315-2.jpg Apex_TD_40-315-3.jpg Apex_TD_40-315-4.jpg

Bauer Coupling Hose Tails - Used

See Below

Make an enquiry

Used Bauers

Type

3"

4"

6"

Male (Used)

7.35 9.18 14.95

Female (Used)

4.37 6.54 9.37

'O' Ring (New)

1.27 1.65 2.30
       

Complete Set

12.97 17.37 26.30
used-bauers-1.jpg used-bauers-2.jpg used-bauers-3.jpg

Wire Armoured Hose

Make an enquiry

Wire Armoured Hose

Heavy duty, rubber flexible suction and delivery hose in 3 or 6m lengths complete with Bauer quick release couplings.

Please click here to view our Hoses and Bauer Couplings Page

1.jpg 2.jpg 3.jpg

Medium Duty PVC Hose with Bauer Couplings

Medium Duty PVC Hose with Bauer Couplings Any length available to suit your application. Enquire for prices. Widely used for tanker slurry. Available from stock. Next day delivery.

"Suitable for use as tanker hose".

Please click here to view our Hoses and Bauer Couplings Page

Plain end - (Coil) PVC Suction Hose

Make an enquiry

Plain end coil PVC Suction

Plain end - (Coil) PVC Suction Hose Plain end coils available to suit your application. Enquire for prices. Widely used for tanker slurry. Available from stock. Next day delivery

"Suitable for use as tanker hose".

Please click here to view our Hoses and Bauer Couplings Page

Denver Orion 200/150F

£5,500

Denver Orion 200/150F heavy duty slurry pump of double adjustment design and high chrome iron wet end construction. The pump is coupled to a 22kW WEG electric motor.

We can fit large motor to meet increased duty’s - P.O.A.

Flow: 1180 l/min
Head: 102 metres
Inlet: 8"
Outlet: 6"

denver-orion-200x150f-1.jpg denver-orion-200x150f-2.jpg denver-orion-200x150f-3.jpg denver-orion-200x150f-4.jpg denver-orion-200x150f-5.jpg denver-orion-200x150f-6.jpg denver-orion-200x150f-7.jpg

Godwin GSP300

New Reduced Price
£2,750

Here we have a used Godwin submersible pump for sale, A GSP300 model capable of max flow rates up to 350m3/hr with discharge heads ranging to 63 metres. Like similar models in the Sub-Prime range these are reliable pumps suited to tough construction jobs, quarrying mining and industrial application. Being a slim-line rugged build they work well in confined spaces. This pump is made of a chromium-alloy, white cast iron impeller and heavy duty rubber coated adjustable wearing parts. Due to the pumps double mechanical seal it works for dry running and is well insulated against leakage.

Click Here To View Our Wide Submersible Range

GodwinD618 1.jpg GodwinD618 2.jpg

Godwin Dual Pump Temporary Fire Fighting System In Enclosure

P.O.A

The ideal mobile, permanent or temporary fire fighting solution. Comprised of two Godwin 125/100/260 pumps delivering a combined duty flow of 6424L/min with a head of 6.839 bar. Both pumps are powered by bespoke water cooled Clarke TK6H NL30 diesel engines which all fits inside a sound attenuated fabricated steel construction high density mineral wool isolation enclosure. This system is IP54 rated in a double skin with motorised ventilation and heating, exhausts internally fitted and again ventilated. This is all controlled by separate control panels on each pump and engine setup, with auto start and system health fail safes for rapid start in the event of emergency. This system is built with reliability in mind the two separate engines which work together to drive two single pumps are isolated by gate values allowing for easy maintenance and adaptable operation. Manufactured in 2004 this system is ready to rent or buy having had a full inspection and service, truly a bespoke build system with only quality parts used in construction .

Click Here to view the datasheet for this fire fighting system

1.jpg 1a.jpg 1b.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg 14.jpg 17.jpg 19.jpg 21.jpg 23.jpg 27.jpg 28.jpg 29.jpg 34.jpg 36.jpg 37.jpg

Godwin CD80

£3,250

Make an enquiry

SP3390 SP3391

Godwin CD80 coupled to a Perkins two cylinder diesel engine. Being a fully automatic, self priming pump mounted on a 4-wheeled site-tow trailer inside a weatherproof canopy.

Serviced and tested prior to sale and will also be re-painted.

Godwin-CD80-1.jpg Godwin-CD80-2.jpg Godwin-CD80-3.jpg Godwin-CD80-4.jpg Godwin-CD80-5.jpg Godwin-CD80-6.jpg Godwin-CD80-7.jpg

Godwin ET 80. new and used in stock

New (with spares kit)
£3,400
Used
£3,000

Make an enquiry

Used - SP3410 SP3411 SP3412 SP3413 New - SP3414 SP3415 SP3416 SP3417 SP3418 SP3419

Available both new and used Godwin ET80 self-priming 3" pumps. Coupled to a Lister hand crank, diesel engine mounted on a skid base with central lifting eye. Ideal for moving dirty water and effluents with upto 25% solid in suspension and no more than 14mm in diameter. Max flow available 80m3/h and max head 40m. Full wear parts and engine filter kit available as extra.

Click Here to view the datasheet for new SP3414

Click Here to view the datasheet for new SP3415

Click Here to view the datasheet for new SP3416

Click Here to view the datasheet for new SP3417

Click Here to view the datasheet for new SP3418

Click Here to view the datasheet for new SP3419

Click Here to view the datasheet for used SP3410

Click Here to view the datasheet for used SP3411

Click Here to view the datasheet for used SP3412

Click Here to view the datasheet for used SP3413

1.jpg 2.jpg 3.jpg 4.jpg

Godwin HL80

£6,500

Godwin HL80 4x3 High Head pump being an automatic, self - priming pump, ideal for quarry work. Powered by a Perkins water - cooled, electric start engine. The pump is mounted in a sound attenuated canopy with a 24 hour chassis fuel tank and four wheeled towable trailer. Delivery available.

Specification
Flow: 28 l/sec
Head: 100 mtr
Hours used: 10000

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg

Godwin CD150M

£4,250

Godwin CD150M fully automatic, self-primimg pump coupled to a Lister 3 cylinder diesel engine, mounted on a skid base with forklift pockets.

Suitable in intermittent flow situations, the CD150M can run dry indefinitely without damage due to the oil bath mechanical seal design.

For sewer bypass, general dewatering, and many other applications. Is not road tow water plant Machinery however the stuart group have an extensive network allowing for fast reliable delivery.

Fully serviced and tested to be in good working order and painted before leaving our depot.

Specification
Flow: 430 m³/hr
Head: 42mtr

Click Here to view the datasheet for SP6447

Click Here to view the datasheet for SP6456

godwin-cd150-1.jpg godwin-cd150-2.jpg godwin-cd150-3.jpg godwin-cd150-4.jpg godwin-cd150-5.jpg godwin-cd150-6.jpg

Godwin Sound Attenuated CD150M

P.O.A

Make an enquiry

SP6463 SP6465 SP6466 SP6467 SP6469

Godwin CD150M sound attenuated, Dri-Prime pumps with options for either road or site tow. Fitted with Perkins diesel engines. These pumps have 6" (150mm) inlet and outlets branches and give indefinate dry-running capabilities. These are ideal for a whole variety of applications from dewatering to sewage bypassing. They offer simple maintenance and are cast iron in construction so sturdy and reliable. All pumps come fully serviced and tested also repainted where required. 5 available

Click Here to view the datasheet for SP6463

Click Here to view the datasheet for SP6465

Click Here to view the datasheet for SP6466

Click Here to view the datasheet for SP6467

Click Here to view the datasheet for SP6469

1.jpg 3.jpg 4.jpg 5.jpg

Godwin HL100M

£17,500

Godwin HL100M pump, powered by a 3 phase 22kW electric motor. Automatic, self priming contractors pump. Previously used in clean water, however these pumps are suitable for abrasive applications and handling solids. 1 in stock.
Delivery available.

Specification
Flow: 210 m³/hr
Head: 115 mtrs

HL100M_1_.jpg HL100M_2_.jpg HL100M_3_.jpg HL100M_4_.jpg

Godwin Sound Attenuated CD100M

P.O.A

Make an enquiry

SP4320 SP4322

Godwin CD100M attenuated, Dri-Prime pumps which are road towable. Fitted with Perkins diesel engines. These pumps have 4" (100mm) inlet and outlet branches and give indefinate dry-running capabilities. These are ideal for a whole variety of applications from dewatering to sewage bypassing. They offer simple maintenance and are cast iron in construction so sturdy and reliable. All pumps come fully serviced and tested also repainted where required. 2 available

Click Here to view the datasheet for SP4320

Click Here to view the datasheet for SP4322

1.jpg 2.jpg

Godwin/SLD MF 55/60 Clean Water Pumps

£49,500 each
Available to Hire
P.O.A

Godwin/SLD MF 55/60 (24") self-priming, clean water pumps, max flow is 5,500m3/hr (1527 l/sec) with a max head of 18mtrs. Fitted with Caterpillar C-12 engines driving the reduction box @ 550RPM. Sold in fully serviced working condition repainted in new owners colours if required. Priced FOB. A selection of pipework and valves are available at extra cost.

2 available

SP8017-1.jpg SP8017-3.jpg cat_c-12.jpg cat_c-12_4.jpg cat_c-12_2.jpg cat_c-12_3.jpg cat_c-12_1.jpg SP8017-4.jpg SP8017-5.jpg SP8017-6.jpg Kirloskar-MF55-60-spec.jpg

Godwin HL150M TS2

To Buy
£34,000

To Hire
Less than 10wks - £665 (p/wk)
10+ Weeks - £612 (p/wk)

Standby Fire Pump
On shore - £450 (p/wk)
Offshore - P.O.A

Godwin HL150M TS2 Ultra High Head pump coupled to a Volvo water cooled diesel engine. Fitted with an mot valve and spark arrestor. Successfully used in quarry, mine dewatering and temporary fire service, the HL6TS is also used as a temporary replacement for permanently installed pumps.

Flanged high pressure hoses also available P.O.A.

Godwin-HL150M-1.jpg Godwin-HL150M-2.jpg Godwin-HL150M-3.jpg Godwin-HL150M-4.jpg Godwin-HL150M-5.jpg Godwin-HL150M-6.jpg

GR Series P-4

£1,950

The P-4 Series provides among the most efficient self-priming, solids handling pump available. This bareshaft pump has a unique hydraulic design and small wall volute casing to minimise friction loss and drag.

The multi-vane open impeller is designed for high efficiency operation while still handling solids up to 28.6mm spherical diameter.

to Flows and heads are dependent on motor size which are available at an extra cost.

Max Head: 40m
Max Flow: 160m³/hr
Casing: Grey iron No.30
Impeller Shaft: Alloy steel No.4140
O-Rings: Buna - N

Pump would be supplied fully serviced and with 3 months warranty.

Click To View Our Data Sheet With More Technical Information

U4B605-B-1.jpg U4B605-B-2.jpg U4B605-B-3.jpg

GR Series P-6

£2,750

The Super U Series provides among the most efficient self-priming, solids handling pump available. This bareshaft pump has a unique hydraulic design and small wall volute casing to minimise friction loss and drag.

The multi-vane open impeller is designed for high efficiency operation while still handling solids up to 31.7mm spherical diameter. ;Flows and heads are dependent on motor size, available at additional cost.

Max Head: 40m
Max Flow: 355m³/hr
Casing: Grey iron No.30
Impeller Shaft: Alloy steel No.4140
O-Rings: Buna - N

Pump would be supplied fully serviced and with 3 months warranty. Click To View Our Data Sheet With More Technical Information

U6B605-B-1.jpg U6B605-B-2.jpg

Grundfos CR2-110

£475

Grundfos CR2-110 vertical multistage centrifugal pump with in-line oval flange connection included.

Used for clean water only. Suitable for washing systems, water treatment systems, industrial plants and boiler systems. We have two in stock

Coupled to a 1.1kW / 415V / 2850 rpm electric motor made by Grundfos.

Supplied fully serviced and includes 3 months warranty.

Max Flow: 3.4 m³/hr
Max Head: 90 mtrs
Speed: 2850 rpm
Intlet/Outlet: 1"

Click To View Our Data Sheet With More Technical Information

grundfos-cr2-110-1.jpg grundfos-cr2-110-2.jpg grundfos-cr2-110-3.jpg grundfos-cr2-110-4.jpg

Grundfos CR 64-5-1 A-F-A-V-HQQV

£2,000

Grundfos CR 64-5-1 A-F-A-V-HQQV in-line pump coupled to a Siemens 30kW 3 phase electric motor - which is currently configured for 50Hz but can be configured for 60Hz.

Flow: 64 m³/hr
Head: 129.2mtr. One in stock

Grundfos_CR64-1.jpg Grundfos_CR64-2.jpg Grundfos_CR64-3.jpg Grundfos_CR64-4.jpg Grundfos_CR64-5.jpg Grundfos_CR64-6.jpg Grundfos_CR64-7.jpg

Hilta Sprite Pump - Petrol

£650 each

Hilta Sprite 2" diaphragm pump powered by a Honda GX120 petrol engine. In good working order complete with 6 metres of suction pipe and strainer along with 6 metres of layflat delivery hose. Mounted on a two-wheeled trolley, ideal for site-use. The pumps are in excellent condition.

Specification:
Flow Rate: 11.3m³/hr
Head: 18 metres
Solids Handling: 20mm construction water pumps

Hilta-Sprite-Pump-1.jpg Hilta-Sprite-Pump-2.jpg Hilta-Sprite-Pump-3.jpg Hilta-Sprite-Pump-4.jpg Hilta-Petrol-Sprite-Pump-1.jpg Hilta-Petrol-Sprite-Pump-2.jpg Hilta-Petrol-Sprite-Pump-3.jpg Hilta-Petrol-Sprite-Pump-5.jpg Hilta-Petrol-Sprite-Pump-8.jpg

Hilta Sprite Pump - Diesel

£850 each

2" Hilta Sprite Pump coupled to a Yanmar diesel engine with electric start. The pump is mounted on a two wheeled trolley with fold away handles. Will pump semi-solids and muddy water making it ideal for site use. Comes with 6 metres of PVC suction hose and 6 metres of layflat discharge hose.

Specification:
Flow Rate: 11.3m³/hr
Head: 18 metres
Solids Handling: 20mm construction water pumps

Hilta-Diesel-Sprite-Pump-1.jpg Hilta-Diesel-Sprite-Pump-2.jpg Hilta-Diesel-Sprite-Pump-3.jpg Hilta-Diesel-Sprite-Pump-4.jpg Hilta-Diesel-Sprite-Pump-5.jpg Hilta-Diesel-Sprite-Pump-6.jpg Hilta-Diesel-Sprite-Pump-7.jpg

Haskel Gas Booster pump

£6,400

Haskel Gas Booster Pump, Double acting single stage pump, 286 bar and operational at between -29 to 40 degrees C, This pump system has a max gas inlet pressure of 400 bar, 6000psi, gas outlet pressure of 700 bar, 10000psi. Produced in February 2012 and formally utilized by BP British Petroleum for sale in an unused condition.

1.jpg 2.jpg 3.jpg

Hilta D5

from
£1,250 each

Hilta D5 Diaphragm Trench Pump coupled to a Yanmar electric start diesel engine. Very little usage. Comes complete with 6 mtrs of suction and 6 mtrs of layflat hose - fitted with Bauer couplings. More than 10 in stock.

As new with Yanmar type engine and electric start: £2,750.00
Used with Yanmar type engine and electric start: £1,750.00
Used with Lister engine and hand crank: £1,250.00
More than 10 available.

IMGP7978.JPG HiltaD5-1.jpg Hilta-D5-2.jpg Hilta_D5_1.jpg Hilta_D5_2.jpg Hilta_D5_3.jpg Hilta_D5_4.jpg Hilta_D5_5.jpg Hilta_D5_6.jpg Hilta_D5_7.jpg Hilta_D5_8.jpg

Ingersoll Dresser Pump 32WJ160

P.O.A

We have an as new Ingersoll Dresser pump for sale. This pump is the model number 406950 0020 01. This pump is 4KW and it can pump up to 60 gpm. Very rarely used and in an as new condition, viewing is welcome and should you have any questions with regards to your pump needs our dedicated sales team will be glad to help source the model, make and type to suite.

Please click here to view a DataSheet for this pump

1.jpg 2.jpg

Kirloskar DSM 125-4

P.O.A

Make an enquiry

SP9049 - SP9062

Kirloskar 150mm x 125mm DSM 125-4 split-casing pump being two stage impeller manufactured in quality cast iron, bronze type wear rings, stainless steel shaft with multi ring packed glands and outboard bearing.

This is a new pump.

Coupled to a refurbished Caterpillar 3306 DT water cooled diesel engine with variable speed throttle, with 24 volt electrics and control panel.

This pump is fitted with SPP Automatic Priming equipment with a 25CFM vacuum pump being oil lubricated. All mounted on robust chassis fuel tank frame with central lifting frame and fork lift pockets.

Typical applications are: Pipeline testing and piging, mine dewatering, sealed cable ploughing installation, hydro mining and fire installation. This pump should not be used on abrasive pumping duties for long periods.

Two pumps available to matched specification so ideal duty and standby application.

All guards are fully fitted to CE requirements.

Max Head: 160 metres
Max Flow: 430m³/hr
Please consider the suction lift derate for NPSHr
Typical duty: 150 metres head / 275m³/hr @ 145kW

Kirloskar-DSM-125-4-1.jpg Kirloskar-DSM-125-4-2.jpg Kirloskar-DSM-125-4-3.jpg Kirloskar-DSM-125-4-4.jpg Kirloskar-DSM-125-4-5.jpg Kirloskar-DSM-125-4-6.jpg Kirloskar-DSM-125-4-7.jpg Kirloskar-DSM-125-4-8.jpg Kirloskar-DSM-125-4-9.jpg

Lowara SV808R40T

£585

ITT Lowara / Xylem SV808R40T vertical multi-stage centrifugal pump with A151304 top and bottom ports with round flanges.

Suitable for water distribution, irrigation, heating, ventilation, pressure boosting, cooling/chilling, water treatment, fire fighting equipment and general industry use.

Supplied fully serviced and complete with 3 months warranty.

Max Flow: 14 m³/hr
Max Head: 100 mtr
Inlet/Outlet: 1 ½"
Pump Body: Stainless Steel
Impeller/Diffuser: Stainless Steel
Seal Holder: Stainless Steel
Adapter: Cast Iron
Elastomers: EPDM
Mechanical Seal: Silicon-carbide/carbon/EPDM
Other hard faced/hot water options available at extra cost.

lowara-sv808r40t-1.jpg lowara-sv808r40t-2.jpg lowara-sv808r40t-3.jpg lowara-sv808r40t-4.jpg lowara-sv808r40t-5.jpg

Metso-Orion MR150

£12,500

Metso-Orion MR150 Hard Iron chrome steel, heavy duty slurry pump. Primed via Selwood auto prime, coupled to a TEFC 75kW 4 pole three phase 50 Hz electric motor. (Only used on clean water). Duty 40 metres x 300m3 Hr (166 LPS). Skid base plus lifting frame.

SP8009.jpg

Molex 4" slurry pump

£5,000

For sale we have a Molex 4" slurry solids handling pump which is driven from an electric start 3 cylinder Perkins water cooled engine. This unit comes mounted on a 2 wheel road tow trailer, sold in good working order serviced and tested. Former regional water companies pump it can be guaranteed that the pump was well maintained corresponding with low running hours. This road towable pump has clock recorded usage of 2623.7hrs

1.jpg 2.jpg 3.jpg

Mono CAE12H1A3/H1103

£1,650

Mono Merlin Pump capable of self priming, smooth pumping action which maintains the product integrity. This simple construction results in a pump that is extremely reliable and easy to maintain. It can be utilised to handle abrasive, shear, sensitive & viscous materials, soft solids in suspension & air/liquid/solid mixtures.

Comes with 10 metres of cable.

Max Head: 45m
Max Flow: 25m³/hr
Outlet/Inlet: 80mm / 3"
Max Solids: 32mm (soft)

Pump Make Up

Body Material: Cast Iron
Pump Design: Industrial Standard
Pump Displacement: 25.5m³/h @ 960 rpm
Pump Stages: 1
Drive Arrangement: Standard
Stator Type Including End Cover: FM Stator & Sep. Str. Thro EC
Mark Number: 1983
Stator Material: Natural Rubber 69-75IRHD
Rotating Part Materials
Rotor/Shaft/Coupling Rod: 316S16 HCP Stainless Steel Rotor – 220M07 Mild Steel Shaft

Click To View Our Data Sheet With More Technical Information

mono-cae12h1a3-1.jpg mono-cae12h1a3-2.jpg mono-cae12h1a3-3.jpg mono-cae12h1a3-4.jpg mono-cae12h1a3-5.jpg

Mono CAE12H1R4/H1

£495

Mono Merlin range Pump capable of self priming. This particular range of pump is suited to many types of application and is extremely diverse in its use. This range of pump is often used in moving materials such as liquid PVC, a magnitude of chemicals, raw sewage and cattle slurry. This model is common place in a manufacturing environment, the food industry and mining. This particular pump was manufactured in 1996 and offers a suction size of 100mm.

Inital technical details include:
Model: CAE12H1R4/H1
Pump Speed: 960RPM MAX
Suction Size: 100mm/4"
Discharge Size: 80mm/3"
Y.O.M: 1996

Click To View Our Data Sheet With More Technical Information

1.jpg 2.jpg 3.jpg

Mono SAB12H1H5/H1117

£1,450

Make an enquiry

SP9104 / SP9108

Mono Merlin Pump capable of self priming, smooth pumping action which maintains the product integrity. This simple construction results in a pump that is extremely reliable and easy to maintain. It can be utilised to handle abrasive, shear, sensitive & viscous materials, soft solids in suspension up to 16mm & air/liquid/solid mixtures.

Comes with 10 metres of cable. Drive belt guard to be fitted.

2 available

Max Head: 45m
Max Flow: 6m³/hr
Max Solids: 16mm (soft)

Pump Make Up

Body Material: Stainless Steel
Pump Design: Industrial Standard
Pump Displacement: 6m³/h @ 1450 rpm
Pump Stages: 1
Drive Arrangement: Standard
Stator Type Including End Cover: FM Stator & Sep. Str. Thro EC
Mark Number: 1983
Stator Material: Hypalon Chlorosulphonated Rubber
Rotating Part Materials
Rotor/Shaft/Coupling Rod: 316S16 Stainless Steel Rotor – 316S16 Stainless Steel Shaft

Click To View Our Data Sheet With More Technical Information

mono-sab12h1h5-h1117-5.jpg mono-sab12h1h5-h1117-6.jpg mono-sab12h1h5-h1117-7.jpg mono-sab12h1h5-h1117-1.jpg mono-sab12h1h5-h1117-2.jpg mono-sab12h1h5-h1117-3.jpg mono-sab12h1h5-h1117-4.jpg

Pioneer SC86 Pump

£17,500

Pioneer SC86C17L72-BG Pump coupled to an AmTecs 3 phase motor (110kW / 191 Amps @ 50Hz / 1490RPM). Ideal sand and gravel, washing plant pump.

We are able to cut the impellor to meet your needs and reduce the power requirement.

This pump comes supplied with a 6 month warranty, Comes fitted with an automatic priming system.

Pioneer_SC86C17-1.jpg Pioneer_SC86C17-2.jpg Pioneer_SC86C17-3.jpg

Primeroyal API-675 Methanol Injection Pumps

Price for both
£6,000
Each
£3,500

We have (x2) unused Primeroyal API-675 Methanol Injection Pumps

They are double diaphragm pumps and have come from major oil company deemed surplus to requirements. Skid Mounted. We will freight to any permitted country at extra cost. Please advise of your petro chem industry needed.

Specification:
Model: API-675 PN175S(V)63H44DX
Maximum Capacity: 3.78 m/h at 44 barg
Motor: 11kw, 415v, 50hz, 3ph, 1473rpm
Y.O.M: 2006

SP8087_32_.jpg SP8087_15_.JPG SP8087_22_.JPG SP8087_23_.JPG SP8087_29_.JPG SP8087_31_.JPG

Road Transportation Suction Dredger

£45,000

Consisting of main pontoon with control cabin. 2 side pontoons & 2 extension pontoons. A Warman 8-6 gravel pump driven by 110kW, 6-cylinder DAF turbo engine driven through twin disc gearbox. 35ft ladder, 2 winch operated spud legs at stern with hydraulic bow thruster. This allows the dredger to walk without shore winches. 200mm x 80 metres floating pipeline and floats available as added extra P.O.A.

Flow: 360m3/hr
Pressure: 3 Bar

A generator can be supplied at extra cost.
Currently being repainted.

Hire Rates
£950 per week (less than 15 weeks)
£650 per week (more than 15 weeks)

For more information and dredging equipment see our Dredging Division

Dredger(1).jpg Dredger(2).jpg Dredger(3).jpg Dredger(4).jpg Dredger(6).jpg Dredger(7).jpg Dredger(8).jpg road-transportation-suction-dredger-1.jpg road-transportation-suction-dredger-2.jpg road-transportation-suction-dredger-3.jpg road-transportation-suction-dredger-4.jpg

Selwood D75

only
£3950

Selwood D75 3 inch Self Priming contractor pump. This pump is the first model in the D range of Selwood Pumps and has all the well known features of reliability, with a proven mechanical shaft seal, reliable priming and great performance. It is coupled to an industry standard, air - cooled, Hatz diesel engine.
The pump will self prime to 9.1mtrs and pump water at up to 60m³/HR (220gpm). Solids handling to 29mm.
We offer all pumps with warranty as we fully service and test all units to ensure serviceability as well and repaint where required or to customer spec.

5.jpg 6.jpg 7.jpg 8.jpg

Selwood D200

£7,900

Selwood D200 pump powered by a Isuzu 4 cylinder diesel engine all on a skid base chassis fuel tank, This pump comes to you fully serviced and tested. Supplied with six metres of new suction hose and also a new set of bauer couplings, 20 metres of 8" layflat and coupling. We will also supply an 8" strainer.

Click To View Our Data Sheet with more technical information

7.jpg 9.jpg

Selwood H100HM

£22,000

Make an enquiry

SP9131 SP9127

H100HM pumps supplied in a good used condition. Selwood manufactured pumps which utilize Volvo TD730VE 6 cylinder, water-cooled, diesel engines. Coupled to Metso Svedala 4x4" high head, high chrome pumps. Being very suitable for abrasive water, slurries and liquids containing solids. This type of pump is fully automatic, self-priming using a Selwood air pump and separator tank. The above is mounted on a robust chassis fuel tank with lifting frame for ease in site allocation. Presently painted in original black / yellow. We are able to offer this pump fully serviced, tested and re-painted.

Click To View Our Data Sheet With More Technical Information

1.jpg 2.jpg 3.jpg 4.jpg

Selwood H100HM

P.O.A

Selwood H100HM pump with a 6" suction size and ball type NRV utilizing two 5" outlets. Being very suitable for abrasive water, slurries and liquids containing solids. The pump is fully automatic, self-priming using the Selwood air pump and separator tank. The above is mounted on a robust chassis fuel tank with lifting frame. Presently painted in original black / yellow. We are able to offer this pump fully serviced, tested and re-painted. Click To View Our Data Sheet with more technical information

2.jpg 1.jpg 4.jpg 5.jpg 6.jpg

Selwood D80 Sound attenuated

£7,400

Selwood D80 contractors pumps coupled to water cooled electric start diesel engines. The pumps are formally part of a regional water company fleet, fully automatic and self-priming. Mounted in 58dBA @ 7 meters sound attenuated enclosures, all contained on either 2 wheel road tow trailers. We are selling these units in good working order, fully serviced and tested on purchase with a UK 3 month warranty. Click To View Our Data Sheet for more technical information.

1.jpg 2.jpg 3.jpg 6.jpg 7.jpg 8.jpg

Selwood D80 Open

P.O.A

Selwood D80 contractors pumps coupled to water cooled electric start diesel engines. The pumps are formally part of a regional water company fleet, fully automatic and self-priming. A site tow option which has all the positives of the sound attenuated unit yet smaller and easier to manoeuvre. We are selling these units in good working order, fully serviced and tested on purchase with a UK 3 month warranty. Click To View Our Data Sheet for more technical information.

10.jpg 11.jpg 12.jpg 13.jpg

Selwood D200

P.O.A

A high flow , high efficiency pump capable of indefinite dry running featuring automatic self-priming. Pump is of robust construction with quick-release couplings and can discharge 600m3/hr when used with clean water. Ideal pump for use on construction and civil engineering clean and dirty water applications.

2.jpg 3.jpg 4.jpg 5.jpg

Selwood S150 Non-containerised

P.O.A

We have three Selwood S150 non-sound attenuated pumps in stock. Offering the end user a max flow of 320m3/h with a maximum head to 21.3m, the inlet and outlet of these pumps are DN150 PN6, the impeller type is a vortex measuring 235mm. This pump can handle of solids up to 100mm. Powered by Duetz 4L41C diesel engines with a maximum rpm of 1600, the engines are housed in containers allowing easy access for maintenance however the pump end is open. These are site towable only, are sold in good working order and ideal for various applications including raw or screened sewage, bentonite, sludge and slurry and are often used in marine, industrial, water waste and also differing construction jobs. These are popular as rental options due to a proven design making them very reliable. Click To View Our Data Sheet With More Technical Information On Our Selwood S150 Open Sets

2.jpg 3.jpg 4.jpg 5.jpg

Selwood S150 Super Silent Canopy

P.O.A

We have six Selwood S150 sound attenuated super silent canopy pumps in stock. Offering the end user a max flow of 320m3/h with a maximum head to 21.3m, the inlet and outlet of these pumps are DN150 PN6, the impeller type is a vortex measuring 235mm. This pump can handle solids up to 100mm. Powered by Duetz 4L41C diesel engines with a maximum operational rpm of 1600. The engines are housed in super silent containers. These units are sold in good working order and ideal for various applications including raw or screened sewage, bentonite, sludge and slurry and are often used in marine, industrial, water waste and differing construction jobs with the added benefit in comparison to the unattenuated version that they can be used in populated areas. These are popular as rental options due to a proven design making them very reliable needing minimal maintenance. Click To View Our Data Sheet With More Technical Information On Our Selwood S150 super silent canopy sets

1.jpg 4.jpg 6.jpg

Selwood 100C

£3,500

Selwood 100C - 4" pump powered by a Deutz electric start, diesel engine, mounted inside a sound attenuated canopy on a skid base. Auto priming, robust and simple to use. 2 available.

Specification
Head: 21.3m
Flow: 160m³/hr
Y.O.M: 1999

selwood-100c-skid-1.jpg Selwood-100C.jpg

Selwood 150C sound attenuated

£4,500

Selwood 150C - 6" pump powered by a Deutz electric start, diesel engine, mounted inside a sound attenuated canopy on a skid base. Auto priming, robust and simple to use.

Specification
Head: 21.3m
Flow: 350m³/hr

selwood-150c-skid-1.jpg selwood-150c-skid-2.jpg Selwood-150C.jpg

Selwood 150c Open

£3,750

Make an enquiry

SP6450 SP6449

We have two Selwood 150c pumps in stock, Selwood manufactured pumps' powered by Hatz 4L41C, Air-cooled, diesel engines. Coupled with a Diaphragm priming type Air Pumps producing max flow at 225m3/h with an impressive max head of 24m and a suction size of 6" or 150mm. Suitable for slurries and liquids containing solids. These are fully automatic. They are mounted on robust chassis fuel tanks with lifting frames at eye lift point. Presently painted in original black / yellow. We are able to offer these pumps fully serviced, tested and re-painted to match your needs, we also supply all hose and bauer fittings to match your job, can source most parts and if unsure of buying used goods can even consultate on comprehensive servicing agreements.

Max Head: 24 mtrs
Max Flows: 225m³/hr
Max Solids: 38mm

Click To View Our Data Sheet With More Technical Information

150c1.jpg 150c2.jpg 150c3.jpg

Selwood H150

£22,000

Selwood manufactured pumps with Volvo TD730VE 6 cylinder, water-cooled, diesel engines. Coupled to a Metso Svedala 6x4" high head, high chrome pump. Being very suitable for abrasive water, slurries and liquids containing solids. The pump is fully automatic, self-priming using the Selwood air pump and separator tank. The above is mounted on a robust chassis fuel tank with lifting frame. Presently painted in original black / yellow. We are able to offer this pump fully serviced, tested and re-painted - 5 available

Comes with warranty ready for your project!

Specification
Y.O.M: 1999

selwoodh1503.jpg selwoodh1504.jpg

Selwood H125

£24,500

The Selwood H125 mounted in a sound attenuated canopy to 62dBA @ 7m. Skid mounted with forklift pockets. Driven by a Isuzu 6cylinder electric key start diesel engine with running hours of 2937.

Specification:
Max Flow: 240m3hour
Max Head: 157m
Suction Size: 6" DN125
Pump Speed: 2400rpm

Please follow this link to view a datasheet for SP9075

1.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg

Selwood S100

P.O.A

Selwood S100 for sale. With a max flow of 165 m3/m and maximun head of 21mts. The unique original Selwood self priming system utilising a water tolerant diaphragm air pump. An environmentally friendly design that has none of the problems of oil vapour emissions and oil emulsification associated with other priming systems, With DN 100mm inlet and outlets. Both of these have Duetz diesels engines and are site towable. Click Here To View Our datasheet for more technical information<

1.jpg 4.jpg 5.jpg 6.jpg

Spate 3B EM

£2,750

The Spate 3B pump can handle dirty water, slurries, light and heavy oils. Can also handle petroleum industry products, including some of the more viscous liquids, at a high, non turbulent flow rate. 415 volt

Automatic priming pump with indefinite dry running ability and includes a stone catcher to prevent larger heavier solids passing through the pump.

Pump is coupled to a 2.2kW, 1420 rpm electric motor.

Max Flow: 30m³/hr
Max Head: 30 mtr
Max Solids: 6mm
Speed: 1420 rpm
Inlet/Outlet: 3" / 80mm

Click To View Our Data Sheet With More Technical Information

spate-3b-1.jpg spate-3b-2.jpg spate-3b-3.jpg spate-3b-4.jpg spate-3b-5.jpg

Spate 75c

£2,550

Spate 75c pump with stone catcher, this pump is powered by a Yanmar diesel engine which is a recoil start. This pump is very versatile and its idea use is working with slurry or similar such material as oils, however they do not deal with large amounts of stone or heavily solids based content, just occassional solids. This pump comes sold fully serviced and also painted if required. as a special offer it comes complete with 6 meters of suction and relay hose.

2.jpg 3.jpg 4.jpg

Duraline Fire Hose

£55.00

We have available ex fire brigade Duraline Fire Hose for sale, in good condition with no leaks. Comes with aluminum instantaneous couplings - 2.5" x 20 metres.

Duraline-Wire-Whipped-Hose.jpg

Armstrong 4x3x13

£7,750

Armstrong 4x3x13 DLC fire pump coupled to a 6 cylinder, turbo charged, Iveco diesel engine. A silencer and flexible bellows are included. Almost new and fully FM approved. Minor repairs to be carried out, supplied in good running order. Installation available. Also available at extra cost is a Grundfos CR2-130 vertical multi-stage jockey pump.

Pump Specification
Flow: 1895 ltr/min
Pressure: 10.8 Bar
Hours: 343
Y.O.M: 1997

Jockey Pump Specification
Flow: 25 ltr/min
Pressure: 10.9 Bar

Need to hire a pump? See our Fire Pump Hire page or contact us.

Armstrong-3x4x13-Fire-Pump-1.jpg Armstrong-3x4x13-Fire-Pump-2.jpg Armstrong-3x4x13-Fire-Pump-3.jpg Armstrong-3x4x13-Fire-Pump-4.jpg Armstrong-3x4x13-Fire-Pump-5.jpg Armstrong-3x4x13-Fire-Pump-6.jpg Armstrong-3x4x13-Fire-Pump-7.jpg Armstrong-3x4x13-Fire-Pump-9.jpg Armstrong-3x4x13-Fire-Pump-10.jpg Armstrong-3x4x13-Fire-Pump-11.jpg

Armstrong 6 BH ELC

£6,500

Armstrong 6 BH ELC fire pump coupled to Iveco 6 cylinder, turbo charged, diesel engine. This pump is perfect for supplying a source of drainage if using a long pipe which we can supply P.O.A

sp9066-armstrong-6bhelc-1.jpg sp9066-armstrong-6bhelc-2.jpg sp9066-armstrong-6bhelc-3.jpg sp9066-armstrong-6bhelc-4.jpg sp9066-armstrong-6bhelc-5.jpg

Armstrong 6x4x10ELC

P.O.A

ARMSTRONG 6x4x10 end suction UL/FM registered fire pump with 150mm suction and 100mm discharge branches. Coupled to a Lister 90kw TEFC 415v, 50hz electric motor. Mounted on a skid base. Fully serviced and tested prior to release including 3 month UK warranty. Can be supplied with standard or Listed starter for additional cost. Two in stock, please follow the links below to view technical specification on these two pumps. Duty: 5044LPM at 7 Bar.

Please follow this link to view a datasheet for SP9177

1.jpg 2.jpg 3.jpg 4.jpg

Armstrong 6x4x10

£11,000 each

£20,000 for a pair

Make an enquiry

SP9115 - SP9116 - SP9177

Armstrong 6x4x10 end suction diesel fire pump. Designed with a heavy duty bearing frame to provide a long and reliable service in an over hung impeller design.

The unit is UL and FM approved and is capable of a flow of 5275 litres per minute at 6.8 bar pressure.

This unit is supplied fully serviced and comes with a 3 month warranty,

View the manufacturers design drawing

3 available.

Max Flow: 8000 l/min
Max Head: 9 bar
Inlet: 6"
Outlet: 4"
Speed: 2960 rpm
Impeller Dia: 259mm
Manufactured: 2004

Features

  • Back pulls out for easy maintenance
  • Self venting centre line discharge
  • Lower NPSH requirements
  • Dependable operation
Click To View Our Data Sheet With More Technical Information

armstrong-6x4x10-1.jpg armstrong-6x4x10-2.jpg armstrong-6x4x10-3.jpg armstrong-6x4x10-4.jpg armstrong-6x4x10-5.jpg armstrong-6x4x10-6.jpg armstrong-6x4x10-7.jpg

Armstrong 8x5x11.5

£12,450

Armstrong 8x5x11.5 DLC fire pump coupled to an Iveco 6 cylinder, turbo charged, diesel engine.

Specification
Pump Duty: 4850 l/min (8.5 Bar)
Max Pressure: 12 Bar
Imp Dia: 283mm

Armstrong-8X5X11-1.jpg Armstrong-8X5X11-2.jpg Armstrong-8X5X11-3.jpg Armstrong-8X5X11-4.jpg

Armstrong 8x6x12.5MF Fire Pump

£8,000

Armstrong 8x6x12.5MF fire pump coupled to Iveco 6 cylinder, turbo charged, diesel engine, impeller diameter is 10.375.

Armstrong 8x6x12MF-1.jpg Armstrong 8x6x12MF-2.jpg Armstrong 8x6x12MF-3.jpg Armstrong 8x6x12MF-4.jpg Armstrong-8x6x12-6.jpg

Armstrong 100-250

£1,000

Armstrong 100-250 fire drive pump coupled to a Brook Crompton CF200MH 55kW motor.
Spec: 3050 l/min 6.6 Bar 55kW

Armstrong AM 2/8 Vertical Multistage 225 pump with 1.1kW Electrodrives motor.
Spec: 25.2 l/min 6.6 Bar 1.1kW

Armstrong_Pumps-1.jpg Armstrong_Pumps-2.jpg Armstrong_Pumps-3.jpg Armstrong_Pumps-4.jpg Armstrong_Pumps-5.jpg Armstrong_Pumps-6.jpg Armstrong_Pumps-7.jpg

Armstrong CR2-130

£200

The Armstrong CR2-130 is a vertical, non-self-priming, multistage, in-line centrifugal pump.

Used for clean water only. Suitable for washing systems, water treatment systems, industrial plants, boiler systems and pumping systems. Made by Grundfos

Coupled to a 1.5kW / 415V / 2890 rpm electric motor made by Grundfos.

Supplied fully serviced and includes 3 months warranty.

Rated Flow: 2.5m³/hr
Rated Head: 81.9 mtr
Speed: 2900 rpm

Click To View Our Data Sheet With More Technical Information

Armstrong CR2_130-1.jpg Armstrong CR2_130-2.jpg Armstrong CR2_130-3.jpg Armstrong CR2_130-4.jpg

Armstrong VMS 1510

£280

Armstrong VMS 1510 vertical multi-stage pump with in line oval flange connection.

Suitable for clean water only. Can be used for pressure boosting, washing systems, water treatment systems, industrial plants and boiler systems.

Close coupled to 1.5kW 3 phase motor.

Supplied fully serviced and comes with a 3 month warranty.

Max Flow: 25.2 l/min
Max Head: 6 bar
Inlet/Outlet: 1 ½"
Speed: 2900 rpm

Click To View Our Data Sheet With More Technical Information

armstrong-vms1510-1.jpg armstrong-vms1510-2.jpg armstrong-vms1510-3.jpg armstrong-vms1510-4.jpg

Crane Fire Pump

£5,000 each
£9,000 both

Crane fire pump model 5B GB/R, FM approved. The pump is a 6 x 5" long coupled to a Firdrive 110 water cooled, turbo-charged engine of 82kW @ 3000 rpm. Hours recended 123 and 4. The control panels are frame mounted to the 8 hour fuel tank. Batteries are Nickel Cadmium, two sets per pump. The silencers are supplied loose. The pumps are viewed as recieved and will be fully serviced and tested per despatch. The non-return and nrv are included in the package.

Specification
Duty Flow: 3775 | 3766 dm³/min
Duty Head: 5.045 | 6.75 Bar
Hours
SP9079: 123
SP9080: 4

Crane-5G-GB-R-Fire-Pump-1.jpg Crane-5G-GB-R-Fire-Pump-2.jpg Crane-5G-GB-R-Fire-Pump-3.jpg Crane-5G-GB-R-Fire-Pump-4.jpg Crane-5G-GB-R-Fire-Pump-5.jpg Crane-5G-GB-R-Fire-Pump-6.jpg Crane-5G-GB-R-Fire-Pump-7.jpg Crane-5G-GB-R-Fire-Pump-8.jpg Crane-5G-GB-R-Fire-Pump-9.jpg Crane-5G-GB-R-Fire-Pump-10.jpg Crane-5G-GB-R-Fire-Pump-11.jpg

Crane Ltd  5B GB R

£750

Crane Ltd Irrigation boost pump
Serial No: 5175-1
Product Code: 5B GB R
Duty Flow: 4000 dm³/min
Duty Head: 8.2 BAR
BHP 150 @ 2900RPM
5" in and out.
Brook Crompton 110kW, 2920RPM electric motor (s/no: T992P).

Crane_Ltd_Pump(1).jpg Crane_Ltd_Pump(2).jpg Crane_Ltd_Pump(4).jpg Crane_Ltd_Pump(6).jpg Crane_Ltd_Pump(8).jpg

Marine Ship Fire Pumps

£9,125

Make an enquiry

New Fire Pumps

We offer a full range of Marine Ship onboard Fire Pumps for emergency duty
Model shown is 7MD/LT1 Other models to meet duty needs. We can supply Hatz diesel hand crank start engines for the 7MD.

With Lister engines.
26 units sold in 2011.

FirePump_1_.jpg FirePump_3_.jpg

SPP KP08E

£2,250

SPP KP08E pump coupled to a Brook Hansen CF200LN 55kW, 415 volt electric motor.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Flow: 500 US GPM
Pressure: 125 PSI
Speed: 2935 RPM
Impeller Dia: 10.04"

spp-kp08e-sp9089-1.jpg spp-kp08e-sp9089-2.jpg spp-kp08e-sp9089-3.jpg spp-kp08e-sp9089-4.jpg spp-kp08e-sp9089-5.jpg

SPP KP10X

£6,250

SPP KP10X fire drive pump and jockey pump coupled to a 4 cylinder Cummins 4BT3.9 LFC turbo charged, diesel engine.
These also make great irrigation pumps.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Specification
Flow: 3050 l/min
Pressure: 6.6 Bar
Hours: 252

Installation available.

SPP-KP10X-1.jpg SPP-KP10X-2.jpg SPP-KP10X-3.jpg SPP-KP10X-4.jpg SPP-KP10X-5.jpg SPP-KP10X-6.jpg SPP-KP10X-7.jpg SPP-KP10X-8.jpg SPP-KP10X-9.jpg SPP-KP10X-10.jpg SPP-KP10X-11.jpg SPP-KP10X-12.jpg SPP-KP10X-13.jpg SPP-KP10X-14.jpg SPP-KP10X-15.jpg SPP-KP10X-16.jpg SPP-KP10X-17.jpg

SPP KP10X

£8,000.00

SPP KP10X 5x4" Fire Drive Pump. These make great irrigation pumps and are powered by a 6 cylinder, turbo charged, Iveco diesel engine. The engine has been re-worked by Firedrive LTD to meet certification and is fitted with 2 sets of ni cad battery’s and two AC chargers. A silencer and flexible bellows are included.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Specification
Flow: 91.70 l/sec
Head: 71.40 mtr

Sold fully inspected and serviced.

Installation available.

SPP-KP10X-1-SP9042-3.jpg SPP-KP10X-2-SP9042-3.jpg SPP-KP10X-3-SP9042-3.jpg SPP-KP10X-4-SP9042-3.jpg SPP-KP10X-4-SP9042-3.jpg SPP-KP10X-5-SP9042-3.jpg SPP-KP10X-6-SP9042-3.jpg

SPP KP12X

£12,500

SPP KP12X fire pump coupled to a Firedriver 175, 130 bhp, 3000 rpm, 6 cylinder diesel engine.

Pump comes fitted with automatic fire control panel which automatically manages operation of the pump when required.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Max Flow: 5888 l/min
Impeller Dia: 264mm
Rated Pressure: 7.39 bar
Max Working Pressure: 12 bar
Manufactured: 2006

spp-kp12x-1.jpg spp-kp12x-2.jpg spp-kp12x-3.jpg spp-kp12x-4.jpg spp-kp12x-5.jpg spp-kp12x-6.jpg spp-kp12x-7.jpg spp-kp12x-8.jpg

SPP KP10X Firepump

P.O.A

SPP fire pump powered by Clarke 6 cylinder diesel engine.

This unit is sold as the engine and pump end only with control panel as an added extra.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world. The Clarke IK4HNL50 engine is capable of producing 84BHP, 2960rpm, 63kW. This engine has a max load of use set at 76BHP, 56kW, 2960rpm. An exhaust is not sold with this unit but can be provided as an added extra.

Specification
Suction Size: 5 inch
Discharge Size: 4 inch
HP: 84
Y.O.M: 2003

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg 13.jpg 14.jpg 15.jpg

SPP TC12G

£13,500

SPP TC12G fire pump coupled to a Caterpillar 3208 diesel engine.

This pump comes fitted with a fire control panel for fully automatic control. Comes with 4 lead acid batteries.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Max Flow: 1480 US GPM
Head: 375 feet
Hours: 240
Manufactured: 1997

sp9095-spp-tc12g-1.jpg sp9095-spp-tc12g-2.jpg sp9095-spp-tc12g-3.jpg sp9095-spp-tc12g-4.jpg sp9095-spp-tc12g-5.jpg sp9095-spp-tc12g-6.jpg sp9095-spp-tc12g-7.jpg sp9095-spp-tc12g-8.jpg sp9095-spp-tc12g-9.jpg sp9095-spp-tc12g-10.jpg

SPP TD15A

£15,500

SPP TD15A split casing fire pump powered by Clarke (Iveco) 6 cylinder, turbo charged engine by 10" x 8". Ex standby pump with low hours. The pump will be fully tested and supplied with exhaust and manual.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Specification
Flow: 7112 l/min
Rated Pressure: 8 Bar
Max Pressure: 16 Bar
Y.O.M: 2000
Hours: 152

Installation available.

SPP-TD15A-Fire-Pump-1.jpg SPP-TD15A-Fire-Pump-2.jpg SPP-TD15A-Fire-Pump-3.jpg SPP-TD15A-Fire-Pump-4.jpg SPP-TD15A-Fire-Pump-5.jpg SPP-TD15A-Fire-Pump-6.jpg SPP-TD15A-Fire-Pump-7.jpg SPP-TD15A-Fire-Pump-8.jpg SPP-TD15A-Fire-Pump-9.jpg SPP-TD15A-Fire-Pump-10.jpg SPP-TD15A-Fire-Pump-11.jpg SPP-TD15A-Fire-Pump-12.jpg

SPP TD15F

£5,500

Make an enquiry

SP9087 - SP9088

SPP TD15F pump coupled to a Brook Hansen CF280SN 132kW, 415 volt electric motor, manaufactured in 1998. 2 available.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Flow: 6000 L/MIN
Speed: 2955 RPM
Pressure: 9 Bar
Impeller Dia: 305mm

spp-td15f-1.jpg spp-td15f-2.jpg spp-td15f-3.jpg spp-td15f-4.jpg spp-td15f-5.jpg spp-td15f-6.jpg spp-td15f-7.jpg spp-td15f-8.jpg spp-td15f-9.jpg spp-td15f-10.jpg

SPP TD15A

£4,250

SPP TD15A fire pump powered by a 4 cylinder GM Bedford diesel engine. Mounted on a skid base with 2 sets of batteries, diesel fire pump panel and integral single skin fuel tank. Fully serviced and tested prior to release along with a 6month standby warranty.SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world. SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world. YOM is 1982, Rated flow 4850DM3/min. The rated pressure is 8.5 bar.

Specification
Suction Size: 200 mm
Discharge Size: 150 mm
Hours: 1914

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg 13.jpg 14.jpg 15.jpg 16.jpg 18.jpg

SPP TD15A

£15,500

SPP TD15A fire pump powered by a 6 cylinder Clarke modified diesel engine. Mounted on a skid base with 2 sets of batteries, diesel fire pump panel, integral single skin fuel tank and exhaust silencer supplied loose. Fully serviced and tested prior to release along with a 6month standby warranty. SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world. SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world. Also available are suction and delivery pipework with non return valve, gate valves including gauges at additional cost. YOM 2009. Rated flow 4850 l/min and rated pressure of 8.5bar.

Specification
Suction Size: 200 mm
Discharge Size: 150 mm NP16 flange
Hours: 51

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg 13.jpg 14.jpg 15.jpg 17.jpg 18.jpg 19.jpg 20.jpg 21.jpg 22.jpg

SPP TD15F

£15,500

SPP TD15F coupled to a Caterpillar 3208, naturally aspirated, water cooled diesel engine.

Comes fitted with fire control panel which is fitted for fully automatic control. Also comes with new lead acid batteries.

This pump will be fitted, fully serviced and tested ready for installation.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Max Flow: 140 l/sec
Head: 112 mtr
Pressure: 11.6 bar
Hours: 315

spp2-td15f-1.jpg spp2-td15f-2.jpg spp2-td15f-3.jpg spp2-td15f-4.jpg spp2-td15f-5.jpg spp2-td15f-6.jpg spp2-td15f-7.jpg spp2-td15f-8.jpg spp2-td15f-9.jpg spp2-td15f-10.jpg

SPP TD15F

£15,500

SPP TD15F coupled to a Firedriver 175 FI 130 bhp / 2800 rpm, 6 cylinder diesel engine.

This fire pump comes fitted with fire control panel for fully automatic control.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Max Flow: 1500 US gpm
Max Head: 400 feet
Impeller Dia: 12.79"
Pressure: 125 psi
Manufactured: 1999

spp-td15f-sp9102-1.jpg spp-td15f-sp9102-2.jpg spp-td15f-sp9102-3.jpg spp-td15f-sp9102-4.jpg spp-td15f-sp9102-5.jpg spp-td15f-sp9102-6.jpg spp-td15f-sp9102-7.jpg spp-td15f-sp9102-8.jpg spp-td15f-sp9102-9.jpg

SPP TD15F

£13,200

SPP TD15F coupled to a Clarke TK6HUF60, up to 177 bhp / 3000 rpm, 6 cylinder diesel engine (engine manufactured 04/2005).

This fire pump is fitted with an automatic fire control panel to automatically manage pump in event of fire.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Max Flow: 1500 US gpm
Max Head: 390 feet
Impeller Dia: 12.79"
Pressure: 125 psi
Manufactured: 1999

spp-td15f-sp9100-1.jpg spp-td15f-sp9100-2.jpg spp-td15f-sp9100-3.jpg spp-td15f-sp9100-4.jpg spp-td15f-sp9100-5.jpg spp-td15f-sp9100-7.jpg spp-td15f-sp9100-6.jpg

SPP TD20D

15,000

SPP TD20D split casing fire pump, coupled to an Iveco Firedriver 275 6 cylinder diesel engine.

Comes fitted with fire control panel for automatic operation in the event of fire.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world. Recently overhauled in our workshop with new set of lead acid batteries, fully serviced, tested and ready for any emergency operation

Flow: 8400 l/min
Pressure: 9 bar
Impeller Dia: 340mm
Year of Manufacture: 1998

sp9105-spp-td20d-1.jpg sp9105-spp-td20d-2.jpg sp9105-spp-td20d-3.jpg sp9105-spp-td20d-4.jpg sp9105-spp-td20d-5.jpg sp9105-spp-td20d-6.jpg sp9105-spp-td20d-7.jpg

SPP AC50/75

Used with road tow trailer
£1,650

As new on trolley (2 available)
£1,825

2" SPP ACE50/75 coupled to a Lister-Petter single cylinder, air-cooled (AD1), diesel engine. The pump is mounted on a, two-wheeled, road-tow trailer.
The Autoprime ACE50 pump is manufactured by SPP, the market leading manufacturer. This is a compact diesel driven pump unit designed for ease of handling and ability to pump liquids containing sand, sewage and small semi solids. Typical uses are removal of ground and rain water from excavations, trenches, footings, manholes and ponds etc.

Specification:
Flow Rate - 37 m3/h
Discharge Head - 28m
Working Pressure - 10 bar

Design Features:

  • Barrow handled site trailer with central lifting point.
  • Compact design will pass through a domestic door frame
  • Reliable double mechanical seals which allow dry running.
  • 24 Hour fuel tank
  • Pump can be left running when liquid is exhausted and will self prime when liquid is present.
Click To View Our Data Sheet With More Technical Information

spp_al50-75(1).jpg spp_al50-75(3).jpg spp_al50-75(5).jpg spp_al50-75(6).jpg ACE50-1.jpg ACE50-2.jpg ACE50-3.jpg SPP-ACE50-1.jpg SPP-ACE50-2.jpg SPP-ACE50-3.jpg

SPP ACE80 / 100RT

£3,500

SPP ACE80 / 100 coupled to a Hatz 1D90, electric start, diesel engine. All mounted on a road tow trailer. The Bauer couplings will be replaced and the pump will be fully serviced prior to sale. The SPP Pumps Autoprime ACE100 pump is a compact diesel driven pump unit designed for ease of handling and ability to pump liquids containing sand, sewage and small semi solids. Typical uses are removal of ground and rain water from excavations, trenches, footings, manholes and ponds etc. May also be used for stream and pipe diversions and flood water control.

Specification:
Flow Rate - 136 m3/h
Discharge Head - 25m
Working Pressure - 10 bar

Design Features:

  • Road trailer with ball or ring hitch, and central lifting point.
  • Pump will pass solids up to 1.6" (40mm) diameter.
  • Reliable double mechanical seals which allow dry running for extended periods.
  • Pump will prime itself automatically when liquid is present and can be left running unattended.
SPP_ACE80-100-1.jpg SPP_ACE80-100-2.jpg SPP_ACE80-100-3.jpg SPP_ACE80-100-4.jpg SPP_ACE80-100-5.jpg

SPP AL100M

£4,500

SPP AL100M coupled to either a Lister TR2 or Isuzu 3CD1, 3 cylinder diesel engine with electric start. Mounted on a 4 wheeled, site tow trailer. The SPP Autoprime AL100 pump is a diesel driven pump unit designed to pump liquids containing sand, sewage and semi solids. Typical uses are removal of ground and rain water from excavations, trenches, footings, manholes and ponds etc. May also be used for stream and pipe diversions and flood water control.

Specification:
Flow: 150m³/hr
Head: 25mtr
Solids: 44mm (dia)

Design Features:

  • Site trailer with four wheels for stability and fold up tow/draw bar.
  • Pump will pass solids up to 44mm diameter.
  • Reliable double mechanical seals which allow dry running.
  • Pump can be left running when liquid is exhausted and will self prime when liquid is present.
  • Pump will run on load for 21 hours before refuelling

View more pumps like this - Sykes GP100M -

SPP-AL100M-5.jpg SPP-AL100M-6.jpg

SPP HH150

£34,500
(subject to availability)

SPP Autoprime HH150, high head 200x150mm (8"x6") pump driven by a diesel engine generally comprising of a twin blade stainless steel impellor with cast iron wear plates, on a stainless steel shaft supported by ball (DE) and roller (NDE) bearings. The shaft is sealed by market leading double face silicon carbide mechanical seals running in an oil reservoir, enabling long periods of dry-running.

Ex demo pump with around 1,500hrs

1835.jpg 1836.jpg SPP-HH150-1.jpg SPP-HH150-2.jpg

SPP HH150

£16,000

SPP HH150 high head pump coupled to a Brook Crompton 37kW 415V electric motor - 1500RPM. Suitable for dirty water applications such as slurry or sewage. Fitted with an automatic vacuum priming system for rapid priming. Ideal quarry wash water pump. 200mm suction inlet and 150mm flanged outlet.

Max Flow: 100LPS / 360m³/hr
Head: 50mtrs @ 5.4 Bar

SPP_HH150-1.jpg SPP_HH150-2.jpg SPP_HH150-3.jpg SPP_HH150-4.jpg SPP_HH150-6.jpg SPP_HH150-5.jpg

SPP XH-150

£43,250.00

Hire From
£1,300.00 Per week

The Sterling SPP AUTOPRIME XH150 pump is designed for applications where a very high lift is required. These will include mines and quarries and major works such as tunnels and deep foundations.

Used widely in gold mining and offshore cable ploughing / burying by towing ships.

Fitted with Caterpillar engine.

Year of manufacture: 2002.
1 sold 3 still available

Flow: 400m³/Hr
Head: 160mtr
Solids Handling: 62mm (dia)

Dimensions:
L: 4000mm W: 1375mm

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg spp-xh150-1.jpg spp-xh150-2.jpg spp-xh150-3.jpg spp-xh150-4.jpg spp-xh150-5.jpg spp-xh150-6.jpg spp-xh150-7.jpg spp-xh150-8.jpg

NEW - SPP AL150M

£13,858

Make an enquiry

New AL150M

Stuart Pumps Ltd are an authorised distributor of SPP's Autoprime range and have a large stock of new SPP pumps. The SPP Autoprime AL150M pump is a high performance diesel driven pump unit designed to pump liquids containing sand, sewage and semi solids. The AL150M is an automatic, solids handling, self-priming pump coupled to a Lister TR3 diesel engine with electric start and is mounted on a 4-wheeled trailer with 24 hour fuel tank. Typical uses are removal of ground and rain water from excavations, trenches, footings, manholes and ponds etc. May also be used for stream and pipe diversions and flood water control.

Specification:
Flow: 285m³/hr
Head: 25mtr
Solids: 53mm (dia)

Design Features:

  • Site trailer with four wheels for stability and fold up tow/draw bar.
  • Pump will pass solids up to 52mm diameter.
  • Reliable double mechanical seals which allow dry running.
  • Pump can be left running when liquid is exhausted and will self prime when liquid is present.
  • Pump will run on load for 25 hours before refuelling

Extras:
Spark Arrestor - £345.00
Spark Arrestor & Chalwyn Valve - £860.0

IN STOCK READY FOR NEXT DAY DELIVERY

CLICK HERE TO VIEW OUR CURRENT STOCK OF SPP PUMPS

SPP_AL150-150M.jpg tech.jpg

NEW - SPP QHH80

£21,275

The SPP Autoprime QHH80 pump is designed for high head and modest flow applications including jeting, washing and in mines and quarries where a high lift is required. Solids handling is limited by the use of a high performance design for the impeller.

Specification:
Flow Rate - 120 m3/h
Discharge Head - 89m
Working Pressure - 10 bar

Design Features:

  • 12 volt battery starting by key switch.
  • 65 cfm Vacuum Pump with coalescer and air filtered before exhaust to atmosphere.
  • Reliable double mechanical seals which allow dry running.
  • Pump will pass solids up to 9.2mm diameter.
  • Pump can be left running when liquid is exhausted and will self prime when liquid is present.

CLICK HERE TO VIEW OUR CURRENT STOCK OF SPP PUMPS

SPP-QHH80-Skid.png

SPP QI150

MORE STOCK WANTED

The SPP AUTOPRIME QI150 pump is a fully enclosed diesel driven pump unit with high efficiency, designed to pump most liquids including sewage and semi solids.

The enclosure provides sound reduction and security for use in noise sensitive areas. Typical uses are removal of ground and rain water from excavations, trenches, footings, manholes and ponds etc. May also be used for stream and pipe diversions and flood water control, well point dewatering, pipe relining and sludge pumping.

Flow: 380m³/hr
Head: 25mtr

Available Extras

Spark Arrestor
High Speed Trailer

SPP-QI150-Spark_Arrestor-1.jpg SPP-QI150-Spark_Arrestor-2.jpg SPP-QI150-Spark_Arrestor-3.jpg SPP-QI150-Spark_Arrestor-4.jpg SPP-QI150-Spark_Arrestor-5.jpg SPP-QI150-Spark_Arrestor-6.jpg SPP-QI150-Road-Tow-1.jpg SPP-QI150-Road-Tow-2.jpg SPP-QI150-Road-Tow-3.jpg

Sykes GP50

£1,300

Sykes GP50 2" self-priming pump coupled to a Lister 1 cylinder diesel engine. All mounted on a 2-wheeled site-tow trolley.

This is a compact diesel driven pump unit designed for ease of handling and ability to pump liquids containing sand, sewage and small semi solids. Typical uses are removal of ground and rain water from excavations, trenches, footings, manholes and ponds etc.

Specification:
Flow Rate - 37 m3/h
Discharge Head - 28m
Working Pressure - 10 bar

Design Features:

  • Barrow handled site trailer with central lifting point.
  • Compact design will pass through a domestic door frame
  • Reliable double mechanical seals which allow dry running.
  • 24 Hour fuel tank
  • Pump can be left running when liquid is exhausted and will self prime when liquid is present.
sykes-gp50-1.jpg sykes-gp50-2.jpg sykes-gp50-3.jpg sykes-gp50-4.jpg sykes-gp50-5.jpg

Sykes GP80

£3,250

Sykes GP80 3" self-priming pump coupled to a Lister TR1 diesel engine. All mounted on a 2-wheeled site-tow trailer.

More stock available.

Sykes-GP80-1-SP3396.JPG Sykes-GP80-2-SP3396.JPG Sykes-GP80-3-SP3396.JPG Sykes-GP80-4-SP3396.JPG Sykes-GP80-5-SP3396.JPG Sykes-GP80-6-SP3396.JPG

Sykes GP100m

£4,200

SPP AL100M / Sykes GP100M fully-automatic, self-priming pump coupled to a Lister TR2 diesel engine with electric start and pipeline frame.

The pump has recently been fully refurbished and serviced by Stuart Pumps Ltd. It is an automatic, self priming pump, is mounted on a skid base.

White protective frame has now been removed. New pictures to follow after pump has gone through workshop.

Sykes-GP100M-2-Skid.jpg Sykes-GP100M-1-Skid.jpg Sykes-GP100M-3-Skid.jpg Sykes-GP100M-4-Skid.jpg Sykes-GP100M-5-Skid.jpg Sykes-GP100M-6-Skid.jpg Sykes-GP100M-7-Skid.jpg Sykes-GP100M-8-Skid.jpg

Sykes / SPP GP100M

£4,500

SPP / Sykes GP100M 4" pump coupled to a Lister Petter TS2 diesel engine with electric start. The pump has recently been fully refurbished and serviced by Stuart Pumps Ltd. It is an automatic, self priming pump and is mounted on a 4 - wheeled chassis with a 24 hour fuel tank.

sykes-gp100m_1.jpg sykes-gp100m_2.jpg sykes-gp100m_3.jpg sykes-gp100m_4.jpg sykes-gp100m_5.jpg sykes-gp100m_6.jpg sykes-gp100m_7.jpg sykes-gp100m_8.jpg sykes-gp100m_9.jpg

Sykes / SPP GP100M

£4,500

SPP / Sykes GP100M 4" pump coupled to a Lister Petter TS2 diesel engine with electric start. The pump has recently been fully refurbished and serviced by Stuart Pumps Ltd. It is an automatic, self priming pump and is mounted on a 4 - wheeled chassis with a 24 hour fuel tank. These are great multi-purpose pumps and will suit a wide range of applications. Very robust and reliable pumps.

Sykes-GP100M-SP4187-1.jpg Sykes-GP100M-SP4187-2.jpg Sykes-GP100M-SP4187-3.jpg Sykes-GP100M-SP4187-4.jpg Sykes-GP100M-SP4187-5.jpg Sykes-GP100M-SP4187-6.jpg Sykes-GP100M-SP4187-7.jpg Sykes-GP100M-SP4187-8.jpg

SPP Autoprime Ace80

P.O.A

SPP Autoprime Ace80 fitted with a Lister-Petter diesel engine. Max flow of 100m3/h the max head is 25m with a suction size of 80mm or 3". This pump has a discharge of 80mm or 3" with solids handling of 40mm, the pump speed is 2000rpm. 12v on a key start it comes with a 55 litre capacity fuel tank and is open skid. Manufactured in 1999 this pump comes in good working order having been serviced at point of sale. Click To View Our Data Sheet With More Technical Information

1.jpg 2.jpg 3.jpg

Sykes / SPP GP100M

£5,000

SPP / Sykes GP100M 4" pump coupled to a Lister Petter TR2 diesel engine with electric start. It is an automatic, self priming pump and is mounted on a 4 - wheeled chassis with a 24 hour fuel tank. These are great multi-purpose pumps and will suit a wide range of applications. Very robust and reliable.

Specification:
Flow: 150m³/hr
Head: 25mtr
Hours: 4033

Comes with 6 month warranty.

Sykes-GP100M_SP4302-1.jpg Sykes-GP100M_SP4302-2.jpg Sykes-GP100M_SP4302-3.jpg

Sykes / SPP GP100M

£3,995
Now: £3,400

We have a Sykes / SPP GP100M pumpsets being automatic, solids handling, self - priming pumps. The pumps are coupled to a Lister LPW3, water - cooled, electric start, silent diesel engine and mounted on 24 hour chassis fuel tank with lifting and tow bar.
Delivery available.

More units may be available.

SP4154_1_.jpg SP4154_2_.jpg SP4154_3_.jpg SP4154_5_.jpg SP4154_6_.jpg

Sykes / SPP GP100M

£3,400

Sykes / SPP GP100M pumpset being automatic, solids handling, self - priming pumps. The pump is coupled to a Lister LPW3, water - cooled, electric start, silent diesel engine and mounted inside a sound attenuated canopy on a 4-wheeled road-tow trailer. Some minor repairs to be carried out, sold in good working order. Can be re-painted at extra cost.

Hours: 7446

Sykes-gp100-sp4296-1.jpg Sykes-gp100-sp4296-2.jpg Sykes-gp100-sp4296-3.jpg Sykes-gp100-sp4296-5.jpg

Sykes / SPP GP100M

£3,500

Sykes / SPP GP100M pumpset being an automatic, self - priming, contractors, solids - handling pump. The pump is coupled to a Hatz 2L40, silent pack, diesel engine. The pumpset is mounted on a 4 - wheeled chassis.
Delivery available.

SP4167_1_.jpg SP4167_2_.jpg

SPP AL100M

£4,500

SPP AL100M 4" pump coupled to a Lister Petter TR2 diesel engine with electric start. It is an automatic, self priming pump and is mounted on a skid base with a 24 hour fuel tank.

gp100m-skid-sp4303-1.jpg gp100m-skid-sp4303-2.jpg gp100m-skid-sp4303-3.jpg gp100m-skid-sp4303-4.jpg

Sykes / SPP GP150M 

£6,000

Sykes / SPP GP150M pumpset. The pump is an automatic, self - priming pump, coupled to Lister TR3, electric start, diesel engine. Mounted on a 4-wheeled, site tow trailer. Comes with 3 month warranty. Hours are unknown but have been advised low. Photo as taken in, to be fully serviced.

Sykes-GP150M_SP6430-1.jpg Sykes-GP150M_SP6430-2.jpg Sykes-GP150M_SP6430-3.jpg

Sykes GP150M (SP60)

P.O.A

The GP 150M is a general purpose industry standard for Construction, Utilities and Civil Engineering. Used wherever there's a need for positive self - priming, with a unique Sykes Univac vacuum system. The pump is auto self priming from dry. The GP 150M, is powered by a 20kw Lister engine. Sold used in good condition we can offer this pump to you re-painted and fully serviced. This is a site towable pump which is easy to use and maintain. The pump output is a maximum 90l/m with a max total head of 38m. This unit is the perfect all in one contruction site pump solution, also ready as a rental solution.Click To View Our Data Sheet With More Technical Information for SP6457< /p>

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg 13.jpg 14.jpg

Sykes / SPP GP150M

£5,250

Sykes / SPP GP150M pump. Automatic, self - priming pump, coupled to Lister LPW4, electric start, silent diesel engine. Mounted on a skid base.
To be fully re-conditioned.
Delivery available (4 - 6 weeks).

IMGP7660.JPG IMGP7661.JPG IMGP7662.JPG IMGP7663.JPG

Sykes UV150M

£3,500

Sykes UV150M coupled to a Lister HR3 diesel engine on a 4 wheeled trailer. It is an automatic, self priming, contractor pump with good solids handling.
Shown in photos as incomplete but will be fully-tested and complete before sale.

Selwood-UV150M-1.jpg Selwood-UV150M-2.jpg Selwood-UV150M-3.jpg Selwood-UV150M-4.jpg

Sykes GP200M

£9,250

Sykes GP200M fully automatic self-priming pump, coupled to a 4 cylinder Iveco 8045 turbo-charged diesel engine.

All mounted on a 4 wheeled road-tow trailer.

New mud guards now fitted.

1 available.

sp6433-sykes-gp200m-1.jpg sp6433-sykes-gp200m-2.jpg sp6433-sykes-gp200m-3.jpg sp6433-sykes-gp200m-4.jpg sp6433-sykes-gp200m-5.jpg sp6433-sykes-gp200m-6.jpg sp6433-sykes-gp200m-7.jpg sp6433-sykes-gp200m-8.jpg

Sykes GP200M

P.O.A

GP 200M is the general purpose industry standard for Construction, Utilities and Civil Engineering. Specifically designed for arduous applications, the GP 200M power comes from its 65kw water cooled diesel engine and incorporates the unique Sykes Univac vacuum system. This pump is sold in great condition it has only covered 1009 hours of use. This pump can discharge 138 l/s against a maximum total head of 36m. Pump also supplied complete with attached 6” gate valve.

Click To View Our Data Sheet With More Technical Information for SP6554

1.JPG 2.JPG 3.JPG 4.JPG 5.JPG 6.JPG 7.JPG 8.JPG 9.JPG 10.JPG 11.JPG 12.JPG 13.JPG 14.JPG

Sykes Special Build

£3,750 each

This pump was built by Sykes as a special build for a local water companies.
It will pump a large percentage of solids at a flow of approximately 272m3/hr (1000gpm) with heads of around 3.5 Bar.
Fully automatic priming via vacuum pump. The engine is a Lister HL6 with electric start.
Ideal for agricultural slurry pump or industrial applications. We are selling as it has not been used often enough.
Sold fully serviced and in working order.
Delivery available.
Gate valve available as added extra.

SP346_2_.jpg SP346_3_.jpg SP346_4_.jpg SP346_5_.jpg SP346_new_.jpg

Sykes UVC3

TSI
£2,750

STI
£2,250

Electric motor
£2,600

Make an enquiry

SP3405 SP3406 SP3403 SP3402 SP3434

Sykes Univac UVC3 with air cooled engines or electric motor to power, they have 5.5 kw starter boxes' and are button push start. The chassis are open and non-sound attenuated. TSI + STI engines or 4KW Electric motor options in stock, The pumps are auto self priming pumps which offer 250gpm pumping ability with solids handeling of up to 50mm. These pumps are approx 920mm in length with a 520mm width, 1100mm height. The Max flow for these pumps is 65m3/h with max head at 15m and the suction size is 3"/75mm. These units come mounted on 24 hour fuel tanks

Click To View Our Data Sheet With More Technical Information for SP3406

Click To View Our Data Sheet With More Technical Information for SP3405

Click To View Our Data Sheet With More Technical Information for SP3403

Click To View Our Data Sheet With More Technical Information for SP3402

Click To View Our Data Sheet With More Technical Information for SP3434

Sykes_UVC3(1).jpg Sykes_UVC3(2).jpg Sykes_UVC3(3).jpg Sykes_UVC3(4).jpg Sykes_UVC3(5).jpg

Sykes UVC4

£1,750

Sykes UVC4 4" pump powered by a Lister HR2, air-cooled, diesel engine, which are good for 20,000 operating hours.

Mounted on a skid base and a 24 hour capacity fuel tank chassis. Can be fitted to site tow 2 wheel trailer for an additional £175.

This pump has an electric start and will self prime to 8 metres.

Minor works to be carried out pre sale included in listing price.

Sold with 3 months warranty.

Max Flow: 135 m³/hr
Max Head: 35 mtr

Click To View Our Data Sheet With More Technical Information

sykes-univac-1.jpg sykes-univac-2.jpg sykes-univac-3.jpg sykes-univac-5.jpg sykes-univac-6.jpg sykes-univac-7.jpg sykes-univac-9.jpg

Sykes UVS

£6,000

Sykes UVS 12" pump coupled to a Lister HRS6 turbo diesel air-cooled engine. The pump is a fully-automatic, self-priming pump and will handle large solids. Previously used by a local water company as standby unit. Price includes full service and re-paint.

Max Head 25 metres at 230l/s

SP312_1_.jpg SP312_2_.jpg

H-4 Trash Pump

£1,300

This is a 4" self-priming centrifugal, high-head, trash pump. It is a highly efficient pump with heavy duty construction ideal for sewage applications. The large volute design allows it to reprime automatically. The pump was only used for 5 months on a gravel wash plant - sold in good working order.

H6-Trash-Pump-1.jpg H6-Trash-Pump-2.jpg H6-Trash-Pump-3.jpg H6-Trash-Pump-4.jpg

Sulzer Bingham Oil Pipeline Pumps

Unit Price
£10,000

All three
£27,000 FOB UK Port

Make an enquiry

SP7009, SP7010, SP7011

Oil Pipeline Pumps Sulzer Bingham Williamette Ltd. W 2745mm x L 3235mm x 2450mm. 16 x 18 x 20 HSB. Flow 21,575 gpm. Head 715 ft. Manufactured for BP Trading Ltd. Onshore/Offshore oil pipeline boost pumps with crude oil product, pumps are skid based and were coupled to Ruston Gas Turbines of 5,000 HP. The pumps are believed to have been reworked, but this is not guaranteed. Open to any inspection.

Sulzer_10_.jpg Sulzer_1_.jpg Sulzer_2_.jpg Sulzer_3_.jpg Sulzer_4_.jpg Sulzer_5_.jpg Sulzer_6_.jpg Sulzer_7_.jpg Sulzer_8_.jpg Sulzer_9_.jpg

DP50

£9,500

We offer a wide range of DP submersible pumps which are specially designed for sand, gravel and handling heavy, abrasive slurries.

These centrifugal pumps with closed impeller, feature a unique agitator design. This agitator lifts sediments into suspension, creating a slurry mixture and enables the continuous pumping of media with a high concentration of solids.

Robust construction, careful selection of materials and unique contour components have produced a pump with excellent abrasion resistance which, coupled with a low speed high torque motor, ensures long service life and economical operation.

For more information on prices and availability for Dredging Pumps.

For more information on prices and availability for Submersible Pumps.

1.jpg 3.jpg

Tsurumi TD300HZDE

£2,450 (includes UK delivery)

 

Hire Rates (p/w)
4 Week: £65.00 
6 Months: £46.00
12 Months: £42.00

The TD300HZDE pump is an automatic priming, diaphragm pumps powered by a Hatz diesel engine (with electric start) and is also trolley mounted. It is fitted with diaphragms (in nitrile rubber), so priming is unnecessary and indefinite dry running is permissible. The pump can handle site water containing sand, silt and solids up to 30mm. The inlet and outlet ports, pump casings and surge reduction chambers are all constructed from aluminium. The rubber diaphragm and check valves are replaceable for easy on site repair, while the gear unit is maintenance free and is grease filled during factory assembly. Maximum suction lift is 8 metres, however 6 metres, or less, is recommended. This extremely popular pump is widely used by utilities and regularly found on hire fleets (see rates).

Supplied with a suction strainer, hose couplings, washers, clips and as part of this offer we are also including 6 metres of PVC suction hose and 6 metres of layflat discharge hose.

Offer only available whilst stocks last!

Tsurumi-TD300HZDE.jpg

Tsurumi LH675

£29,835

List Price Normally
£41,145

Hire Rate
£375 (p/wk)

The LH series are heavy-duty, high head pumps that provide exceptional wear resistance and outstanding performance in the toughest civil engineering or water supply projects. Constructed of cast iron, the centre discharge design reduces the base area size and facilitates locating and positioning in confined spaces. This design also enables efficient motor cooling when pumping small amounts of water or even during dry running conditions. Improved flow on a flyght 2400HT model pump.

The 420 stainless steel shaft is fitted with an ultra hardwearing, silicon carbide, double mechanical seal (in an oil chamber). The LH675 has high water pressure resistance to permit operating in water up to 50 metres deep. In addition, an oil lifter is fitted to maintain seal lubrication during operation in any position. Supplied with 20 metres of heavy duty, H07RN-F rubber power cable, although IDS (individually screened cable) is available, at an extra cost, for quarry and mining applications. Enquire for more information.

Specification
Head: 132 mtr
Flow: 2440 l/min
Outlet: 150mm (BSPM/Flange)

Tsurumi-LH637-1.jpg Tsurumi-LH637-2.jpg Tsurumi-LH637-3.jpg Tsurumi-LH637-4.jpg Tsurumi-LH637-5.jpg

Tsurumi LH837

£10,750

The LH837 pump is a heavy-duty, high head pump that provides exceptional wear resistance and outstanding performance in the toughest civil engineering or water supply projects. Constructed of cast iron, the centre discharge design reduces the base area size and facilitates locating and positioning in confined spaces. This design also enables efficient motor cooling when pumping small amounts of water or even during dry running conditions. Similar flows on a Flygt 2870 model pump. The 420 stainless steel shaft is fitted with an ultra hardwearing, silicon carbide, double mechanical seal. The LH837 has high water pressure resistance to permit operating in water up to 50 metres deep. In addition, an oil lifter is fitted to maintain seal lubrication during operation in any position. Supplied with 20 metres of heavy duty, H07RN-F rubber power cable, although IDS is available, at an extra cost, for quarry and mining applications. Enquire for more information.

Warman 6 x 4 Type D-AH

New lower price
£750

Warman 6 x 4 Type D-AH S/No WP8432

Pump4.jpg

Warman 3 x 2 Type HH

£2,000

Warman 3 x 2 Type HH S/No WP9044

Pump6.jpg

Warman 6 x 4 HH

£2,500

Size 6 x 4 HH Warman Pump WP11231. Ideal for pumping sand, gravel and abrasive materials.

IMGP8050.JPG IMGP8051.JPG IMGP8052.JPG IMGP8053.JPG IMGP8054.JPG IMGP8055.JPG

Warman PC200

£28,500

£4,200 for optional priming gear

Warman PC200 slurry/sand pump powered by a fully reconditioned Caterpillar 3406T diesel engine.

All mounted on a skid base chassis with fuel tank. Fuel tank is 1500mm wide by 110mm high, with an estimated capacity of 2300 litres, offering approximately 8 hours operating time.

Fitted with key start starter panel with various features including hour meter, oil pressure, water temp, water pressure, water vacuum and battery power.

This pump was manufactured for use in dredging or boost pumping.

Inlet/Outlet: 8” – 200mm

 

 

 

Click To View Our Data Sheet With More Technical Information

pc200-1.jpg pc200-2.jpg pc200-4.jpg pc200-5.jpg pc200-6.jpg

Warman 6x4

£6,500

Warman 6X4 AH Rubber Lined with packed gland and overslung 37kW TEFC. A slurry pump which is foot mounted with an overhead of 37kW, the motor is a Brooks Crompton 1450RPM belt driven. This pump is one of our used models in a very good condition reflected with very little use.

Please click here to view a Curve for this pump series

Please click here to view a DataSheet for this pump

1.jpg 2.jpg 3.jpg 4.jpg

Whale Mega Purger Groundwater Sampling Pump

Pump
£145.90

Food Grade with 30m Hose
£20

Make an enquiry

Mega Purger Whale Pump

Groundwater Sampling Pump 40mm OD. Head + 30 metre Cable. 8LPM max flow. 10 amp x 12 volt DC motor.

MegaPurger.jpg

Whale Mini Purger Groundwater Sampling Pump

Pump
£46.70

Food Grade x 15m Hose
£15

Make an enquiry

Mini Purger Whale Pump

Groundwater Sampling Pump 40mm OD. Head + 10 metre Cable. 8LPM max flow. 5 amp x 12 volt DC motor. Outlet 12mm.

MiniPurger.jpg

Whale Super Purger Groundwater Sampling Pump

Pump
£84.95

Food Grade with x 25m Hose
£19.00

Make an enquiry

Super Purger Whale Pump

Groundwater Sampling Pump 40mm OD. Head + 20 metre Cable. 8LPM max flow. 10 amp x 12 volt DC motor.

SuperPurger.jpg

Wilden P.025

£225

Wilden P.025 1/4" made with Teflon Diaphragm so will handle most solvents and oils. Wilden's legendary Original Series pumps are designed for demanding utilitarian type applications that require a robust design. Orginal Series pumps ensure reliability without sacrificing ease of maintenance. Wilden's plastic Original Series lends itself to various processes and waste applications. Port size 1/4"/6mm, fluid diaprhagm per stroke - 0.02ltrs.
Fluid diaphragm per stroke - 0.02ltrs/sec | Typical flow rate - 19 ltr/min

FlowDryWet

18.9LPM
Suction 3.3mtr Suction 9.3mtr
Wilden_P.025-Diaprhagm-Air-Pump.jpg Wilden_P.025-Diaprhagm-Air-Pump-1.jpg Wilden_P.025-Diaprhagm-Air-Pump-2.jpg Wilden_P.025-Diaprhagm-Air-Pump-3.jpg Wilden_P.025-Diaprhagm-Air-Pump-4.jpg Wilden_P.025-Diaprhagm-Air-Pump-5.jpg

Wilden M4/T4

£450

The Wilden M4/T4 2" diaphragm pump is an air-operated, positive displacement, self-priming pump.

Double diaphragm pumps are suitable for pumping water, slurry, sewage, oils, resins, chemicals and more. Can be used for dewatering operations, filling/emptying liquids from tanks/containers and can be used for pumping abrasives or solids.

Read the Wilden M4/T4 manual

Flow: 366.6 l/min
Head: 275 feet
Pressure: 8.6 bar
Max Solids: 3/16" (4.76mm)

wilden-m4-1.jpg wilden-m4-2.jpg wilden-m4-3.jpg

Ingersoll-Rand ARO PD20A

£750

Ingersoll-Rand ARO PD20A 2" air operated double diaphragm pump.

The ARO Diaphragm Pump offers high volume delivery even at low air pressure. ARO pumps feature stall resistant design, modular air motor / fluid sections.

Read the Ingersoll-Rand ARO PD20A manual

Flow: 644 l/min
Head: 285 feet
Pressure: 120 psi
Max Particle Size: 1/4" (6.4mm)

ir-pd20a-1.jpg ir-pd20a-2.jpg ir-pd20a-3.jpg

Blagdon AP50

P.O.A

Blagdon AP50 submersible air powered pump.

Read the Blagdon AP50 manual

Flow: 34 m³/hr
Pressure: 8.6 bar
Max Solids: 6mm

blagdon-ap50-1.jpg blagdon-ap50-2.jpg

Blagdon B5002AA

£750

Blagdon B5002AA 2" air operated double diaphragm pump.

This ball valve type diaphragm pump is powered by compressed air and is a 1:1 ratio design. The diaphragm operates in a balanced condition during the discharge stroke which allows the pump to be operated at discharge heads of over 200 feet (61 meters) of water.

Read the Blagdon B5002AA manual

Flow: 500 l/min
Head: 88 metres
Max Solids: 1/4" (6mm)
Pressure: 8.6 bar

blagdon-b5002aa-1.jpg blagdon-b5002aa-2.jpg blagdon-b5002aa-3.jpg

Custom Pump Building

Bespoke Pumps

Make an enquiry

Custom Pump Building

At Stuart Pumps we have a combined wealth of knowledge and experience in pump specifications to match all your needs, we have produced bespoke pumps which offer a magnitude of functionality. We can build a tailored pump for your circumstances allowing for speed and affordability.

Made To Measure
Affordable
Reliable
Bespoke

custom sprinkler pump.jpg custom mud pump.jpg

Flowserve 4x3x8 GRP

£825

Flowserve 4x3x8 GRP. This pump comes freshly repainted and fully serviced having minimal prior use. It will supply 275gpm with a max head of 60 Ft. With an NP16 suction inlet it is 4" with a discharge of 3". This pump has recently been overhauled by Sulzer pumps.

1.jpg 2.jpg 3.jpg 4.jpg

Blagdon B5001AABBTTT

£750

Blagdon B5001AABBTTT 2" air operated double teflon diaphragm pump.

This ball valve type diaphragm pump is powered by compressed air and is a 1:1 ratio design. The diaphragm operates in a balanced condition during the discharge stroke which allows the pump to be operated at discharge heads of over 200 feet (61 meters) of water.

Read the Blagdon B5001AABBTTT manual

Flow: 567 l/min
Head: 86 metres
Pressure: 125 psi
Max Solids: 1/4" (6mm)

blagdon-b5001aabbttt-1.jpg blagdon-b5001aabbttt-2.jpg blagdon-b5001aabbttt-3.jpg

ABS Vertical turbine pump

£6,750

Make an enquiry

ABS Vertical turbine pump

Now in stock, ABS vertical turbine pump, full details to follow on full inspection by our pump engineering team. A in-culvert lift pump of about 2000lps at 60kW. Stuart Pumps offer competive prices on all online used pumping solutions, fully tested and re-painted where required or to a customers specification.

Calpeda NM25/160AE SP9152

£225

Nearly new Calpeda NM25/16AE Pump with 1.1/2” female BSP suction and 1” BSP female delivery connections. Coupled to a 1.5kw, 415v, 50hz TEFC electric motor. Capable of max flows of 12m 3/h and max heads of 37m.

Please see our DataSheet for more technical information

1.jpg 2.jpg

Ebara 3M 32-1251.1

£250

EEbara 3LM32-125 end suction stainless steel pump with DN50 suction and DN32 delivery branches. Coupled to a 1.1kw, 415v, 50Hz TTEFC electric motor. Capable of max flows of 20m 3/h and max heads of 22.5m. Starter box and cable available as extra.

Please see our DataSheet for more technical information

1.jpg 2.jpg

Ebara EVMW25N

£325

Ebara EVMW2.5N WRAS approved vertical multistage pump. Driven by a 0.55kw 415v/440v 50hz/60hz TEFC motor. Capable of max flow of 3.6m 3/h and max heads of 49.4m. The pump has 1.1/4” BSP female in-line connections. Suitable for pressure boosting applications. Starter box can be supplied at additional cost.

Please see our DataSheet for more technical information

1.jpg 2.jpg

GMP Gussago Gear 1000G

P.O.A

GMP Gussago Gear 1000G pump with 3/4 female BSP suction and delivery branches. Coupled to a 110v electric motor complete with at least 1m of cable and 110v site plug attached. Capable of maximum flows of 16lpm and maximum heads of 100m. Volumetric self priming gear pump with built in by-pass for viscous liquids of 8 degrees C and below. We have two of these in stock please see our below datasheet which stipulates further technical information.

<

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg

Lowara PABLBM15

£120

Xylem / Lowara PABLBM15 pump in near new condition. Coupled to a 240V, 0.37kw, 50HZ, TEFC electric motor. Capable of max head 33, 5m meters and max flows of 2m 3/h. The pump has 1 inch BSP female suction and delivery branches and a bronze body.

Please see our DataSheet for more technical information

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg

Lowara 32-160/03/A

£475

Xylem / Lowara SHE4 32-160/3A centrifugal pump with 316 Stainless steel bodies and impellers. Coupled to a 0.37kw, 415v, 50hz TEFC electric motor. Capable of max heads of 8m and max flows of 15m 3/h. The pump has DN50 suction and DN32 delivery branches. Suitable for pumping hot or cold, mildly aggressive liquids upto a maximum temperature of 85c. Starter boxes, hoses and mechanical seal upgrade for glycol or high temperature available at additional cost. Please see our DataSheet for more technical information <

1.jpg 2.jpg

Lowara SV402T03T

£680

Xylem / Lowara SV402T03T vertical multistage pump complete with variable speed controller. Fitted with a 0.37kw, 415v, 50hz electric motor the integral inverter within the variable speed controller allows for a 240v incoming power supply to drive the pump. Capable of max heads of 18m and max flows of 8m 3/h. Suitable for circulation of hot or cold water for heating, cooling and conditioning systems along with your pressure boosting requirements. Minimise your electric use with a variable speed controller allowing your motor to only use the power necessary to meet your pressure demands. We have a technical data sheet ready for download on the below link . . .

Please see our DataSheet for more technical information

1.jpg 2.jpg 3.jpg

Lowara FHE4 50-200/11

£650

Xylem/Lowara FHE4 50-200/11 cast iron centrifugal pump. Coupled to a 415v, 1.1kw, 50hz electric motor. Suitable for may water moving applications. Max flow 42m 3/h and max head of 12m. Pump starter and hoses also available at additional cost. We have a technical data sheet ready for download on the below link our dedicated sales team can also help with any further information required to find the correct pump for your needs. .

Please see our DataSheet for more technical information

1.jpg 2.jpg 4.jpg

Sulzer High Pressure Industrial Pump

P.O.A

Sulzer multistage high pressure water pump. This pump consists of ring sectons which utilize diffuser casings bolted suction and delivery casing, 50hz and 1450rpm. A head of 850m and delivery size of 250mm these pumps are suited mainly to such as fire fighting the supply of water at high pressure for high risk buildings, mine dewatering and feeding large amount of water for large boiler feeds.

1.jpg 2.jpg 3.jpg

Stainless Steel Flexible Impeller Pump

£180

Make an enquiry

impeller pump

Jabsco 53010 Stainless Steel Flexible Impeller Pump, 1/2". Food Grade Neoprene or Nitrile impeller, Carbon/ceramic mechanical type seal, this unit can be used for the safe pumping of food grade products and materials. This pump can be set up for use as 230 or 110 (vac). the pump weight is 6.3kg, and offers a non pulsating flow, With a Brook Crompton motor these pumps are popular due to their durability. The pump does have slight damage to one bolt hole on one side but still has three good bolt holes allowing it to still be fastened for operations.

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg

Coronet 4 Inch Diesel

P.O.A

Make an enquiry

SP43 16+17+18+19

New to our used stock range, Stuart Pumps can offer four Coronet 4" inch diesel pumps. Power by Lister diesel engines these pumps are mounted on site towable trolleys. The Coronet 20 powered by hand crank air cooled lister engines offer a 4" DN100 suction size with 4" female Bauer and discharge of 4" DN100 also. The shaft has a mechanical seal and the pump is close coupled. Although open chassis and non-sound attenuated this pump and coupled engine is very versatile and manoeuvrable and can be centre point lifted making them the ideal pump where location might impose restrictions on size.

Click To View Our Data Sheet With More Technical Information for SP4319

Click To View Our Data Sheet With More Technical Information for SP4318

Click To View Our Data Sheet With More Technical Information for SP4317

Click To View Our Data Sheet With More Technical Information for SP4316

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9.jpg 10.jpg 11.jpg 12.jpg 13.jpg 14.jpg

Yellow Chemical Cabinet with 2 ARO IR intersol rensol pumps

£2,950

Make an enquiry

ARO IR intersol Rensol

For sale we have a yellow chemical cabinet. This cabinet which has a lockable door and COSHH instructional documentation inside also has two ARO IR Intersol Pumps, Diaphragm Air pumps with a typical flow rate of 35gpm subject to air flow. These pumps are fully self priming, and mounted on a bunded area. The included pumps are in good working order and will be cleaned and test run on purchase

1.jpg 2.jpg 3.jpg 4.jpg

Caprari model MEC/MRH125/2 6x5 Irrigation Pump

£2,300

Caprari model MEC/MRH125/2 twin stage 6x5 irrigation pump, This pump is sold having been used for 1 season with the purpose of jetting mud on an inland water lake. This pump has since been stood stored and unused for 3 years so sold in good order, this pump has a packed gland. Caprari is a very reputable brand of pump, Engine or motor can be supplied at additional cost.

2.jpg 3.jpg 4.jpg 5.jpg

Chassis fuel tank

£550

Make an enquiry

chassis fuel tank

Chassis fuel tank and hydraulic power pack pump. We have three almost new units in stock at a great price. These units had formally been fitted with 3 cylinder Hatz engines which are not included in this sale, replacements can readily be found online. These units could operate with an electric motor, we can provide hose and fittings to assist with making these a very feasible and affordable pump project.

2.jpg 3.jpg 4.jpg 5.jpg

Weir Two Stage Pump

£3,800

Make an enquiry

Weir two stage

Weir two stage pump 100x75mm. These pumps give a typical flow of 350gpm at 120 meters head. This pump is for clean water pumping only, this Weir pump has outbound bearing seals which are packed gland and the day to day or typical operation/application for these might be use as a mains boost. This particular pump could be considered ideal for irrigation as it offers 3-5 times more range then others and is built to last, they are a higher end brand and known to be very reliable and maintenance free.

2.jpg 3.jpg 4.jpg 5.jpg

1.5" Clean Water Pump

£100

1.5inch sef priming clean water pump. Self prime to 7 metres, head 25 metres, flow 24 m3 hr. 75 KW 415 volt motor.

1679.jpg

2" Clean Water Pump

£100

2inch sef priming clean water pump. Self prime to 7 metres, head 25 metres, flow 27 m3 hr. 7.5 KW 415 volt motor.

1677.jpg 1678.jpg

24" Bronze Impeller, Open Channel Pump

£6,000

24inch Pump Bronze Impeller Open Channel 13,500gpm, Belt Driven with Gate Valve, Second of 2 Units. Other Unit working in Salt Works, Kenya.
A diesel engine can be fitted at a total price of £18500.00

SP283.jpg

Ahlstrom Pulp Pump

From
£875

Make an enquiry

Ahlstrom Pulp Pump

We have available (x3) Ahlstrom Paper Pulp Pumps
8 x 8 inch paper pulp end suction pumps with mechanical seals.

These pumps are not great as the volutes have corroded. Bearing pedestals in good working order. If you use these in your pulp mill make an offer using the "Make Enquiry" link.

Non-return valve not included but can be purchased at extra cost.

Spec:
AP44-1200: H= 24m, F= 170 L/s, n= 1480 RPM.
APP33-125: H= 50m, Q= 66 L/s, n= 1480 RPM.
APP44-150: H= 50m, Q= 120 L/s, n= 1480 RPM - SOLD -
APP41-200: H= 24m, Q= 170 L/s, n= 1480 RPM - SOLD -
APP33-125: H= 50m, Q= 66 L/s, n= 1480 RPM.

1661.jpg IMGP8040.JPG IMGP8041.JPG IMGP8047.JPG IMGP8048.JPG IMGP8049.JPG

Oil Pumping Plant

£4,500

For Sale a used oil pumping plant, once used as a backup system for an oil pumping company comes with approx 40 metres of hose on a powered reel, pumping is powered by a hatz diesel engine. Included in the sale is the nozzel and also crane liftable surround. New in stock and to be tested and inspected with further technical details to be confirmed.

1.jpg 2.jpg 3.jpg

6" Liquidator

P.O.A

GSP-340 6 inch Pump powered by a water cooled Perkins 3 cylinder electric start engine. Mounted in a sound attenuated, 65dBA at 7m canopy on a road tow trailer. Suitable for many clean and dirty water applications. Max Flow: 330m3/h. Max Head: 32m. Max Solid: 75mm

6Liquidator_1_.jpg 6Liquidator_2_.jpg 6Liquidator_3_.jpg 6Liquidator_4_.jpg 6Liquidator_5_.jpg 6Liquidator_6_.jpg 6Liquidator_7_.jpg 6Liquidator_8_.jpg 6Liquidator_9_.jpg

Sykes Orion Hard Iron

Sold

Sykes Orion Hard Iron 10 x 8" Pump manufactured in hard chrome steel, coupled to a Volvo TWD121 Turbo Charged Water Cooled Engine all mounted on a skid base fuel tank. Arranged 12" flanges.
Please make an enquiry, new stock coming in soon.

SP8003_1_.jpg SP8003_2_.jpg SP8003_3_.jpg SP8003_4_.jpg SP8003_5_.jpg SP8003_6_.jpg SP8003_7_.jpg

Sykes / SPP BR08B

Sold

Sykes / SPP BR08B 10 x 8" manual prime, twin stage, pump set. Pump is coupled to a Volvo TD70G turbo charged, radiator cooled, diesel engine. Mounted on a skid base chassis with fuel tank and lifting frame. Split casing pump fitted with 420mm impeller.
Sold fully serviced & ready for use.
Delivery available.

SP8058_10_.jpg SP8058_1_.jpg SP8058_2_.jpg SP8058_3_.jpg SP8058_4_.jpg SP8058_5_.jpg SP8058_6_.jpg SP8058_7_.jpg SP8058_8_.jpg SP8058_9_.jpg

Warman Gravel Pump 10" x 8"

Sold

Warman Gravel Pump 10" x 8" 1 season work on inland barge, with Volvo Penta TWD 123 Intercooled Engine. Deck Mounted. GWO. Please make an enquiry, new stock coming in soon.

SP7082_2_.jpg SP7082_3_.jpg SP7082_4_.jpg

SPP TD20D

Sold

SPP TD20D split casing fire pump, powered by a Caterpillar 3208 egnine. Previously used as a standby set on a major warehouse facility. Supplied with auto start control panel and twin start system with 4 LA batteries. Sealed header tank intercooler.
Data:
- Typical Duty: 2500 USPGM @ 103 PSI
- Power: 207.8 HP
- Speed: 2800rpm
- Y.O.M: 1997
- Hours: 480
Installation available
Exhaust supplied at extra cost.
Comes fully serviced & tested.
FM Approved.

More units available.

SP8092_1_.jpg SP8092_2_.jpg SP8093_1_.jpg SP8093_2_.jpg SP8093_3_.jpg SP8093_4_.jpg SP8093_5_.jpg SP8093_6_.jpg SP8093_7_.jpg

Godwin CD150M EM

Sold

New pump coming (example photos).

Godwin CD150M contractor pump, powered by a 15kW / 415V / 50Hz TEFC electric motor, controlled by a star delta starter box. Mounted on a skid frame with lift beam.
Sold fully serviced & ready for use.
Delivery available.

SP6352_1_.jpg SP6352_2_.jpg SP6352_3_.jpg SP6352_4_.jpg SP6352_5_.jpg

Selwood 80C

Sold

Selwood 3" automatic, self - priming pump with solids handling impeller.
Fitted with 3" bauer couplings.
Coupled to a Lister ST1, air - cooled, diesel engine, running at 1500 - 2000RPM.
All mounted on a 4 - wheeled, site tow, chassis with a 24 hour fuel tank.

Sold with 3 months warranty.

SP3361(2).jpg SP3361(4).jpg SP3361(5).jpg SP3361(6).jpg SP3361(7).jpg SP3361(8).jpg SP3361(9).jpg SP3361(10).jpg SP3361(11).jpg SP3361(12).jpg SP3361(13).jpg SP3361(15).jpg SP3361(16).jpg SP3361(17).jpg SP3361(18).jpg

Volvo TD45B

Sold

Volvo TD45B 4 cylinder diesel engine (608 Hours) radiator cooled coupled to a Warman 6 x 4 AH slurry pump.

Warman6x8_1_.jpg Warman6x8_2_.jpg Warman6x8_3_.jpg Warman6x8_4_.jpg Warman6x8_5_.jpg Warman6x8_6_.jpg Warman6x8_7_.jpg Warman6x8_8_.jpg

GSP-340D

Sold

As new EX DEMO pump 6 months warranty.

GSP-340D 6inch Pump powered by a water cooled Perkins 4 cylinder electric start engine.
Mounted in a sound attenuated canopy, on a 4 wheeled high speed trailer.
Wired for auto stop/start. Less than 500 hours use.

Spec:
Solid Handling (mm): 75 | Max Capacity (Ltr/min): 5,500 | Max. Head (m): 32
Max. Flow (m³ p/hr): 330 | Max. Vacuum (m): 9.2 | Max. Noise (dBA at 7m): 65

1.jpg 10.jpg 11.jpg 12.jpg 13.jpg 2.jpg 3.jpg 4.jpg 5.jpg 7.jpg 8.jpg 9.jpg

4" Liquidator

Sold

Make an enquiry

SP4211, SP4226

GSP-300 4inch Pumps powered by a water cooled Isuzu 3 cylinder electric start engine, all mounted in a sound attenuated canopy.
x2 remaining: (SP4211 / SP4226).

Flow: 2,500 litres per minute
Head: 30m

Liquidator4__10_.jpg Liquidator4__1_.jpg Liquidator4__2_.jpg Liquidator4__3_.jpg Liquidator4__4_.jpg Liquidator4__5_.jpg Liquidator4__6_.jpg Liquidator4__7_.jpg Liquidator4__8_.jpg Liquidator4__9_.jpg

ABS Scanpump

Sold

ABS BA 250/250-32 Scanpump. BA end suction single-stage centrifugal pumps are used for demanding industrial applications to ensure process reliability, high efficiency and low operating costs. They are heavy duty pumps designed for pulp and paper stock, slurries in general, abrasive media and clean liquids.

Specification
Flow: 1000m³/hr
Head: 30m
Pressure: 3 bar

ABS-25-32-Scanpump-1.jpg ABS-25-32-Scanpump-2.jpg ABS-25-32-Scanpump-3.jpg ABS-25-32-Scanpump-4.jpg

Apex SEL 100x65-200 22/2

Sold

Apex SEL 100x65-200 22/2 stainless steel, explosion proof pump powered by a WEG 22kW TEFC electric motor, mounted on a steel bedplate with shaft guard.

This pump is like new and has never been used.

Flow: 80 m³/hour
Head: 50 mtr
Pressure: 16 bar
Inlet: 4"
Outlet: 2.5"
Manufactured: 2005

apex-sel-100-85-200-1.jpg apex-sel-100-85-200-2.jpg apex-sel-100-85-200-3.jpg apex-sel-100-85-200-4.jpg apex-sel-100-85-200-5.jpg apex-sel-100-85-200-6.jpg apex-sel-100-85-200-7.jpg

Aro Diaphragm Pump

Sold

Aro diaprhragm pump ideal for Abrasion and Solids Handling because it doesn't use rotating, sliding seals, process engineers. Ideal for handling tough abrasion applications with bolted construction for safe reliability and ease of assembly.

Specification
120 PSI
8 BAR

Aro-666221-Diaphragm-Pump-1.jpg Aro-666221-Diaphragm-Pump-2.jpg Aro-666221-Diaphragm-Pump-3.jpg

Derrick FLC 2000 De-Sander

Sold

The Derrick FLC 2000 De-Sander is a very special piece of plant which can be used for many applications.

Drilling rig mud recovery, dredging operations, recycling of sand and gravel and recycling of water at wash plants.

Fitted with flame proof motors and panels makes this a go anywhere specification machine. Purchased as a safeguard for a project but was never needed. Was used for a few hours to ensure it would seperate the product if required.

These de-sanders typically cost £51,000 when purchased new so this is a very good deal.

2 available (new and used)

FLC Flo-Line Cleaner Manual

Derrick EX, SGX Vibrator Motors Manual

PLANT 022 copy.jpg PLANT 024 copy.jpg DSCN2661 copy.jpg

CRI S4S8/10 Borehole Pump - New & Unused

Sold

The CRI 4" diameter stainless steel series borehole pumps are made from corrosion resistant stainless steel. Complete with a built in check valve suitable for domestic and civil water supply, irrigation, fountains, industrial and rural water supply, fire fighting units, pressure boosting units, ponds, gardens and sprinkler systems.

This pumps is new, unsused and was only removed from packaging for photos.

Suitable to operate with
Max Temperature: 33°C
Permissible Amount of Sand: 50g
Chlorine Ion Density: 500ppm max
Allowable Solids: 3000ppm max
Hardness: 300 ppm max
pH: 6.5 - 8.5

Max Flow: 3.25 l/sec
Max Head: 60 mtrs
Outlet: 2"/50mm (BSP Female)
Cable Length: 1.5 mtrs

cri-borehole-1.jpg cri-borehole-2.jpg cri-borehole-3.jpg cri-borehole-4.jpg cri-borehole51.jpg

Firedriver 175

Sold

These are Standby Fire Pumps and can be reused for that or other applications. Many have been sold for Irrigation Pumps, as the engine speed can be reduced to provide a lower pressure at almost the same flow. Exhaust is included, so fully ready to use. Hand Priming Pump or Auto Pump can be fitted, and other parts as required. Due to large stocks we can offer a special price of £4,500 each or £8,000 the pair. Sold fully serviced and tested.

Pump Spec
Manufacturer: Armstrong
Model: 8X5X11-5DLG
Serial No(SP9020): 560305-1
Serial No(SP9021): 560305-2
Duty: 6500 lpm / 7.6 bar
Max Pressure: 12 bar
Impeller Dia: 286mm
Y.O.M.: 1997

Engine Spec
Iveco 6 cylinder, turbocharged diesel engine with control panel and batteries.
Manufacturer: Iveco
Power: 126 kW
Speed: 2,900 rpm

Hours
SP9020: 339hrs
SP9021: 340hrs

armstrong-fire-pump-1.jpg armstrong-fire-pump-2.jpg armstrong-fire-pump-3.jpg armstrong-fire-pump-4.jpg armstrong-fire-pump-5.jpg armstrong-fire-pump-6.jpg armstrong-fire-pump-7.jpg armstrong-fire-pump-8.jpg armstrong-fire-pump-9.jpg armstrong-fire-pump-10.jpg Fireddrive-175_2.jpg Fireddrive-175_1.jpg

Grundfos FK125 Fire Pump

Sold

Grundfos FK125-250-160 fire pumps with John Deere 4 cylinder diesel engines. Ex standby pumps. Will be fully tested, supplied with exhaust and manual. 2 available.

Specification
Flow: 2570 l/imn
Rated Pressure: 8.50 Bar
Max Pressure: 9.12 Bar

Grundfos-FK125-Fire-Pump-1.jpg Grundfos-FK125-Fire-Pump-2.jpg Grundfos-FK125-Fire-Pump-3.jpg Grundfos-FK125-Fire-Pump-4.jpg Grundfos-FK125-Fire-Pump-5.jpg Grundfos-FK125-Fire-Pump-6.jpg Grundfos-FK125-Fire-Pump-7.jpg Grundfos-FK125-Fire-Pump-8.jpg Grundfos-FK125-Fire-Pump-9.jpg Grundfos-FK125-Fire-Pump-10.jpg

SPP KP12X

Sold

SPP KP12X fire drive pump manufactured by in 2004.
Powered by a Clarke 6 cylinder, turbo charged, header tank cooled engine. Fitted with engine water jacket heater and an auxillary electric engine oil, pre-start, charge pump.
All mounted on a skid chassis with control panel and 8 hour run fuel tank with batteries.
When sold all systems are serviced and tested.
Pipe fittings on suction and delivery extra.
Exhaust silencer and bellows included.
Witness test can be arranged at extra cost.

2 available.

Specification
Flow: 4532 l/min
Pressure: 8.97 Bar
Max Working Pressure: 12 Bar

Hours
SP9032: 47
SP9033: 48

SPP-KP12X-1.jpg SPP-KP12X-2.jpg SPP-KP12X-3.jpg SPP-KP12X-4.jpg SPP-KP12X-5.jpg SPP-KP12X-6.jpg SPP-KP12X-7.jpg SPP-KP12X-8.jpg SPP-KP12X-9.jpg SPP-KP12X-10.jpg SPP-KP12X-11.jpg SPP-KP12X-12.jpg

SPP TD20E

Sold

SPP TD20E split-casing, FM Approved, fire pump.
This pump is powered by an Iveco, 6 cylinder, turbo-charged, fire-drive engine.
Fitted with new twin starter battery, battery charger, control panel and
sealed header tank intercooler.
Sold fully-serviced & tested.
Silencer supplied loose.
Installation available.
Comes with 3 months warranty (subject to satisfactory installation).

Spec:
Engine Model: 8061.25
Pump Model: FD275
Serial: 422694 / 422697
Rated Capacity: 2000gpm
Pressure: 125PSI
Impeller Dia: 12.4 inches
Speed: 2800RPM
Date of Manufacture: 18/12/97
Weight: 1950kG
Hours -
SP9015: 160

SPP_TD20E(1).jpg SPP_TD20E(2).jpg SPP_TD20E(3).jpg SPP_TD20E(4).jpg SPP_TD20E(5).jpg SPP_TD20E(6).jpg SPP_TD20E(7).jpg SPP_TD20E(8).jpg SPP_TD20E(9).jpg

Caprari MEC-MR50/3A

Sold

Caprari MEC-MR50/3A irrigation pump coupled to a Lister TS2 with electric start. The pump is mounted on a skid base and has had a full pump rebuild including shaft and impellors.

Caprari_MEC-MR50-3A-1.jpg Caprari_MEC-MR50-3A-2.jpg Caprari_MEC-MR50-3A-3.jpg Caprari_MEC-MR50-3A-4.jpg Caprari_MEC-MR50-3A-5.jpg Caprari_MEC-MR50-3A-6.jpg

Flotec Purapress

Sold

The Flotec Purapress is a self priming pump with the use of a foot valve & strainer. Ideal to boost domestic water pressure direct from a water well or storage tank.

Comes complete with 24 litre pressure vessel to maintain an on demand water pressure via the attached pressure switch.

Pump body is made from polypropylene which makes it suitable for drinking water supplies.

Please note, additional treatment may be required for your water supply.

Max Head: 46m
Max Flow: 3.6m³/hr
Voltage: 230v

purapress1.jpg purapress2.jpg purapress3.jpg

Flowserve 50-32 CPXM 250

Sold

New and unused Flowserve CPXM series pump. Surplus to project needs.

Close coupled to a 15kW, 415V, 3 phase motor ideal for most transfer applications. The pump end conforms to ISO 2858 dimensional and technical standards.

The CPXM provides a compact, space saving arrangement ideal for industrial processes or installations when space is at a premium.

Max Flow: 30m³/hr
Max Head: 70 mtr
Inlet/Outlet: 50mm / 32mm
Speed: 2940 rpm

Click To View Our Data Sheet With More Technical Information

flowserve-1.jpg flowserve-2.jpg flowserve-3.jpg flowserve-4.jpg

Godwin CD80

Sold

Godwin 3" CD80 self-priming pump coupled to a Lister-Petter TS1 single cylinder diesel engine. All mounted on a 2-wheeled site-tow trailer.

godwin-cd80-sp3394-1.jpg godwin-cd80-sp3394-2.jpg godwin-cd80-sp3394-3.jpg godwin-cd80-sp3394-4.jpg

Godwin CD80

Sold

Godwin CD80 3" self-priming pump coupled to a Lister 1 cylinder diesel engine. All mounted on a 2-wheeled road tow trailer.

godwin-cd80-sp3398-1.jpg godwin-cd80-sp3398-2.jpg godwin-cd80-sp3398-3.jpg godwin-cd80-sp3398-4.jpg

Godwin RDP50/75

Sold

Godwin RDP50/75 3". This is a Rapid Dry Prime, auto self-priming, clean or dirty water pump coupled to a Lister-Petter LT1 air cooled, diesel engine. The pump is mounted on a two-wheeled trolley. Ideal for site use.

Specification
Flow: 50 m³/hr
Head: 22 mtr

Godwin-RDP50-75.jpg

Godwin CD100M

Sold

Godwin CD100M fully automatic, self-primimg pump coupled to a Lister 2 cylinder diesel engine with electric start. The pump is mounted on a 4-wheeled site tow trailer. Suitable in intermittent flow situations, the CD100M can run dry indefinitely without damage due to the oil bath mechanical seal design. For sewer bypass, general dewatering, and many other applications.

Specification
Flow: 160 m³/hr
Head: 35mtr

2 available

Godwin-CD100M-1.jpg Godwin-CD100M-2.jpg Godwin-CD100M-3.jpg Godwin-CD100M-4.jpg Godwin-CD100M-5.jpg Godwin-CD100M-6.jpg

Godwin CD80M

Sold

Godwin CD80M pump on a high speed trailer, mounted inside a sound attenuated enclosure. Fitted with a Perkins engine. The Godwin Dri-Prime 3" (75mm) CD80M automatic priming centrifugal pump is a compact and highly maneuverable portable pumping system that can deliver a maximum of 28.4 l/sec and total dynamic heads to 28.3M.
Indefinite dry running is acheived with Godwin's oil bath mechanical seal design. Solids handling, dry-running and portability make the CD80M ideal for small dewatering and bypass applications.

Specification
Head: 29 mtr
Flow: 28 l/sec
Hours: 1,287

Godwin-CD80D-1.jpg Godwin-CD80D-2.jpg Godwin-CD80D-3.jpg Godwin-CD80D-4.jpg Godwin-CD80D-5.jpg

Godwin CD100M

Sold

Godwin CD100M Hush Pac, 100mm x 100mm pump coupled to an Isuzu 3CD1-DZP04 diesel engine. This pump is mounted in a 2 wheel road tow enclosure. Manufactured by Godwin Pumps UK. In very good condition.

Flow: 230 m3/hr
Head: 38 metres
Pressure: 3.8 bar
Impeller Dia: 230mm
Max Solid Handling: 45mm
Hours: 867

godwin-cd100m-sp4310-1.jpg godwin-cd100m-sp4310-2.jpg godwin-cd100m-sp4310-3.jpg godwin-cd100m-sp4310-4.jpg godwin-cd100m-sp4310-5.jpg godwin-cd100m-sp4310-6.jpg godwin-cd100m-sp4310-7.jpg godwin-cd100m-sp4310-8.jpg godwin-cd100m-sp4310-9.jpg godwin-cd100m-sp4310-10.jpg

Godwin HL80

Sold

Godwin HL80 4x3 High Head pump being an automatic, self - priming pump, ideal for quarry work. Powered by a Perkins water - cooled, electric start engine. The pump is mounted in a sound attenuated canopy with a 24 hour chassis fuel tank on a skid base. Delivery available.

Specification
Flow: 28 l/sec
Head: 100 mtr

Godwin-HL80-3.jpg Godwin-HL80-4.jpg Godwin_HL80-1_SP8080.jpg Godwin_HL80-2-SP8080.jpg

Godwin CD75

Sold

Godwin CD75 3" auto self-priming, clean or dirty water pump coupled to a single cylinder Lister AD1, diesel, engine with electric start. The pump is mounted on a two-wheeled site trolley. To be fully serviced and re-painted.

Godwin_CD75-1.jpg Godwin_CD75-2.jpg Godwin_CD75-3.jpg

Godwin CD150M

Sold

Godwin CD150M pump with level switch mounted on a road tow trailer. Fitted with an enclosed Perkins 104 engine, two in stock. Both Previously used by water company. The Godwin Dri-Prime 6" (150mm) CD150M automatic priming centrifugal pump is suitable for the temporary portable pumping industry. With solids-handling to 3" (75mm) in diameter. With indefinite dry-running capabilities, the CD150M can be found in a wide variety of applications from dewatering to sewage bypassing.

Specification
Flow: 430 m³/hr
Head: 40 mtr
Hours: 3171

sp6418-cd150m-1.jpg sp6418-cd150m-2.jpg sp6418-cd150m-3.jpg sp6418-cd150m-4.jpg sp6418-cd150m-5.jpg sp6418-cd150m-6.jpg sp6418-cd150m-7.jpg

Godwin CD150M

Sold

Godwin CD150M coupled to a Perkins 404 engine. Manufactured by Godwin Pumps UK. This is a 6"/150mm automatic self priming contractors pump. Will handle waste including sewage to large volume projects.

Mounted in a robust steel sound attenuated enclosure, on a high speed road tow trailer.

This pump is in very good condition.

Flow: 1300 gpm
Hours: 318

godwin2-cd150m-1.jpg godwin2-cd150m-2.jpg godwin2-cd150m-3.jpg godwin2-cd150m-4.jpg godwin2-cd150m-5.jpg godwin2-cd150m-6.jpg godwin2-cd150m-7.jpg

Godwin CD150M EM

Sold

Godwin CD150M contractor pump(on hire), powered by a 15kW / 415V / 50Hz TEFC electric motor which runs at 1450 rpm, controlled by a star delta starter box. Ideal for quarry's, washing plant and water supply.

Mounted on a 4 wheel trolley base.

Sold fully serviced & ready for use. Delivery available.

Flow: 340 m³/hr
Head: 23 mtrs

sp6382_cd150m_em_1.jpg sp6382_cd150m_em_2.jpg sp6382_cd150m_em_3.jpg sp6382_cd150m_em_4.jpg sp6382_cd150m_em_5.jpg sp6382_cd150m_em_6.jpg sp6382_cd150m_em_8.jpg sp6382_cd150m_em_7.jpg

Godwin DPC6HL

Sold

Godwin DPC6HL 6" self priming pump. Sold as is, good working order. Ideal as aggregates washing plant. Coupled to 4 cylinder Ford deisel engine. Mounted on skid base.

godwin-DPC6HL-1.jpg godwin-DPC6HL-2.jpg godwin-DPC6HL-3.jpg godwin-DPC6HL-4.jpg godwin-DPC6HL-5.jpg godwin-DPC6HL-6.jpg godwin-DPC6HL-7.jpg godwin-DPC6HL-8.jpg

Godwin HL125

Sold

Part of our ongoing rental fleet replacement programme including our high head range of 80 - 100 - 125 - 150mm pumpsets. We offer SPP, Godwin and Svedala in our fleet.
Spark arrestors and Chalwyn valves can be fitted for refinery applications.
Heads up to 140mtrs / 14 Bar

SP7089_1.jpg SP7089_10_.jpg SP7089_2.jpg SP7089_3_.jpg SP7089_4_.jpg SP7089_5_.jpg SP7089_6_.jpg SP7089_7_.jpg SP7089_8_.jpg SP7089_9_.jpg

Godwin CD160M

Sold

Godwin CD160M with 4 cylinder, water cooled, Perkins engine (1104D-44TA). Mounted inside a sound attenuated enclosure with a 150ltr bunded base fuel tank. Indefinite dry-running is no problem due to the oil bath mechanical seal design. Solids handling, dry-running and portability make the CD160M ideal for small dewatering and bypass applications. The pump will have Bauer couplings fitted (included in price).

Only 10 hours run so as new but without the lead time.
Can be dispatched immediately for next day delivery.
Warranty for mainland UK only, email us to arrange international warranty.

Specification
Flow: 125 l/sec
Head: 260 ft

Godwin_CD-160M-1.jpg Godwin_CD-160M-2.jpg Godwin_CD-160M-3.jpg Godwin_CD-160M-4.jpg Godwin_CD-160M-5.jpg Godwin_CD-160M-6.jpg CD160M_1.jpg CD160M_2.jpg CD160M_3.jpg CD160M_4.jpg CD160M_5.jpg CD160M_7.jpg

Godwin CD200

Sold

This is a Godwin CD200 pump end, fitted with Sykes priming equipment. The pump is powered by a radiator mounted, turbo charged, intercooled, Perkins 1004 diesel engine. The engine was built for a fire suppression application, hence very low stanby hours. The pump has only been used as a standby and comes with mains heater and battery charger. We intend to service the pump and fit a non-return valve. We will also fit a more appropriate control panel, unless it is to be used on a similar application.

SP8097(3).jpg SP8097(4).jpg IMGP7829.JPG IMGP7830.JPG IMGP7832.JPG

Godwin HL125

Sold

Godwin HL125 high head, self priming pump coupled to a 6 cylinder Volvo TID71A diesel engine.

Ideal for use in aggregates washing or gold / diamond washing / mining.

Mounted on skid frame. Successfully used in quarry, mine dewatering and temporary fire service. Manufactured by Sykes Australia.

godwin_hl125_1.jpg godwin_hl125_2.jpg godwin_hl125_3.jpg godwin_hl125_4.jpg godwin_hl125_5.jpg

Godwin HL160M

Sold

The Sld pumps ltd HL160M features an oil bath mechanical seal design. This allows for dry running for prolonged periods while automatically priming and repriming. Able to perform in the toughest conditions, the HL160M can handle solids up to 35mm in diameter. This makes it an extremely effective pump, suitable for both slurry and clean water applications. The powerful HL160M is suitable for mines, quarries and many other high capacity applications. The pump is coupled to a Caterpillar C15, 315kW (2000rpm) diesel engine.

Specification
Head: 187 mtrs
Flow: 486m³/hr
Y.O.M: 2010

Includes 3 month warranty for UK sales, export sales FOB is included. Due in stock May - will reserve on receipt of order / deposit.

HL160M-1.jpg

Godwin HL6TS

Sold

Godwin HL6TS high head, self priming pump coupled to a 6 cylinder Volvo TD100G diesel engine. Mounted on skid frame. Successfully used in quarry, mine dewatering and temporary fire service, the HL6TS is also used as a temporary replacement for permanently installed pumps.

Ex water company. Low hours. Fully serviced, re-sprayed and ready for work.

Godwin_HL6TS-1.jpg Godwin_HL6TS-2.jpg Godwin_HL6TS-3.jpg Godwin_HL6TS-4.jpg Godwin_HL6TS-5.jpg Godwin_HL6TS-6.jpg Godwin_HL6TS-7.jpg Godwin_HL6TS-8.jpg Godwin_HL6TS-9.jpg Godwin_HL6TS-10.jpg

Godwin HL8

Sold

Godwin HL8 (HL200M) high head, self priming pump coupled with Volvo engine. Mounted on skid frame.

Ex water company. Low hours. Fully serviced and ready for work.

Godwin-HL8-1.jpg Godwin-HL8-4.jpg Godwin-HL8-5.jpg Godwin-HL8-6.jpg Godwin-HL8-7.jpg Godwin-HL8-8.jpg

Gorman Rupp T2

Sold

Gorman Rupp T2
An industrial grade waste, 2" (50mm), water pump. Suitable for almost any application. It will self prime and has a mechanical shaft seal in an oil bath, very easy to clean by pulling the back end cover. Flanged inlet / outlet. The T2 is coupled to a totally enclosed, fan-cooled, 4.0kW ABB 3 phase electric motor with coupling guard. Running at 2800 RPM. Mounted on a galvanised steel bed.

IMGP8097.JPG IMGP8105.JPG IMGP8132.JPG IMGP8133.JPG IMGP8134.JPG IMGP8135.JPG IMGP8137.JPG IMGP8138.JPG IMGP8139.JPG

Godwin HL80

Sold

Godwin HL80 4x3 High Head pump being an automatic, self - priming pump, ideal for quarry work. Powered by a Lister CRK 3, water - cooled, electric start engine. The pump has a 24 hour chassis fuel tank and four wheels, tow and lifting beam.
Delivery available.

SP8082_1_.jpg SP8082_2_.jpg

Grundfos Borehole Pump & Hose

Sold

Make an enquiry

Grundfos Borehole Pump

New Grundfos Pump & Hose (4 New Units In Stock)

New Grundfos Borehole Pump SP8A/12 415v 2.2kW with 30m of cable and
starter box with water probe. Wellmaster 50mm Riser Pipe x 28m long,
2" Wellhead + Clamp and 30m of 2" Wellmaster Surface Pipe with
Camlock Couplings, all mounted on a Steel Robust Frame.

GrundfosPumpHose(1).jpg GrundfosPumpHose(2).jpg

Grundfos NB125-250/262 A-F-A-BAQE

Sold

Grundfos NB125-250/262 A-F-A-BAQE coupled to a Siemens 22kW electric motor. This pump has never been used.

Flow: 296 m³/Hour
Head: 19.6 Meters
Pressure: 16 Bar

sp9090-grundfos-nb125-1.jpg sp9090-grundfos-nb125-2.jpg sp9090-grundfos-nb125-3.jpg sp9090-grundfos-nb125-4.jpg sp9090-grundfos-nb125-5.jpg

Ingersoll Dresser Pump

Sold

Ingersoll Dresser Pump coupled to an Alpak II 7.5kW electric motor.
Industrial clean water pump with mechanical shaft seal.

Spec

22ltr/sec @ 25mtr Head

Size: U-DA132SB 3PH / 50Hz
kW: 7.5
r/min: 2870
V: 380-415 / 660-720
A: 14.4-13.6 / 8.3-7.8
Flange Size: 4½" / 5½"

Ingersoll-Dresser-1.jpg Ingersoll-Dresser-2.jpg Ingersoll-Dresser-3.jpg Ingersoll-Dresser-4.jpg

Ingersoll Dresser Pumps

Sold

Pump data - Type: 150 - 125CPXM250
Q: 175 m³h
H: 12m
RPM: 1450
Y.O.M: 1997
Motor data - Type: W DA16DMJ G192580
kW: 11 V: 380 / 415 A: 22.0 r/min: 1470

Only 1 left!

IP_1_.jpg IP_2_.jpg IP_3_.jpg IP_4_.jpg

Lee Howl Bare Shaft Pump

Sold

Lee Howl split casing pump, This is one of britain's quality pumps manufactured by a company which is part of Rolls Royce. This pump is a 250x200mm split case pump with outboard bearing and soft packed gland seals. Construction is close grain cast iron, bronze and stainless steel. This pump is manufactured for clean water (free of solids) applications, typical flows will be 400-450m3/Hr with a mid range head of about 140ft/44mts head. This pump can utilize electric or diesel motor or be PTO driven. This pump is sold having been fully inspected and serviced.

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg

KSB KRT K 555/517

Sold

KSB KRT K 555/517 submersible motor pump for sewage and effluent. The KSB range are economical and easy to service. They are designed for both temporary and permanent installations.

This pump has proven to be very cost effective as it eliminates the need for expensive structures as well as suction pipework valves. Ex Yorkshire water company unused stock. We have used for a total of 8 weeks. Flanged elbow included.

Can be used for sewage and clean water. Ideal large land drainage projects.

Specification
Flow: 4000m³/hr
Head: 22 mtr
192 Amps
94 kW

KSB_KRT_K1-K2-1.jpg KSB_KRT_K1-K2-2.jpg KSB_KRT_K1-K2-3.jpg KSB_KRT_K1-K2-4.jpg KSB_KRT_K1-K2-5.jpg KSB_KRT_K1-K2-6.jpg KSB_KRT_K1-K2-7.jpg KSB_KRT_K1-K2-8.jpg KSB_KRT_K1-K2-9.jpg KSB_KRT_K1-K2-10.jpg KSB_KRT_K1-K2-11.jpg KSB_KRT_K1-K2-12.jpg KSB_KRT_K1-K2-13.jpg

KSB End Suction Pump

Sold

KSB stainless steel end suction pumps coupled to 75 and 132 kW motors. All new never, commissioned. 2 available
250m³/hr at 20 bar
Y.O.M: 2012
More data to follow.

KSB-End_Suction-Pump.jpg

LaBour PL22502

Sold

LaBour PL22502 end suction pump. Stainless steel wet end. Designed for use with Process, Chemical & Hazardous Liquids. Will be serviced prior to sale.

Specification
Flow: 220m³/hr
Head: 7.4 mtr

LaBour-PL-1.jpg LaBour-PL-2.jpg LaBour-PL-3.jpg LaBour-PL-4.jpg

Metso-Orion 6x4

Sold

Metso-Orion 6x4 high head, hard iron pump coupled to a new Perkins 1006TA diesel engine with spark arrestor exhaust. The pump has been fully rebuilt with a full size impeller of 400mm. Mine pump.

Being a hard iron pump these are ideal for use in drilling industries either as a water flush or reverse circulation pump, as they will hand drill cuttings without issue.

Flow: up to 400m³/hr
Head: up to 92mtrs @ 1800RPM

The new engine will go to 2000rpm for intermitently for Heads up to 125mtr

Second unit to arrive soon with same spec.

Metso-Orion-1.jpg Metso-Orion-2.jpg Metso-Orion-3.jpg Metso-Orion-4.jpg Metso-Orion-5.jpg Metso-Orion-6.jpg Metso-Orion-7.jpg Metso-Orion-8.jpg Metso-Orion-9.jpg Metso-Orion-10.jpg Metso-Orion-11.jpg Metso-Orion-12.jpg

Molex Progressive Cavity Pump 

Sold

Ex water company 100mm Molex Mono Progressive Cavaity Pump. Suitable for many applications including soft solids pumping. Can be used with long suction and discharge pipework as it has good air handling ability. These pumps can be fitted with an oil persistant internal starter, making it suitable for Hydrocarbon pumping. The pump is belt driven via clutch to a 3 cylinder Perkins, water cooled, diesel engine on a 2 wheeled roadt towable trailer.

Hose can be supplied upon request.

Molise-Progressive-Cavity-Pump.jpg

6" Pegson Crusher VS150

Sold

Pegson Crusher VS150 6inch self priming medium head pump, powered by a water cooled Perkins 3152 diesel engine. The pump has a max flow of 350m3 per hour and heads up to 38 metres. The engine is silenced to 85 dBA @ 1 metre. Ideal farm slurry pump / quarry work. 1 owner. Low hours and sold in GWO.

SP6296.jpg

Primax CP-150M

Sold

Primax CP-150M 6" pumpset made by Sykes Pumps. These are fully automatic, self-priming, with soldis - handling of 60mm size. The pump is coupled to a VM air-cooled, diesel engine with 12V electrics. It has a skid base 24 hour fuel tank, full wrap round protector, bauer coupling ready for any project. Fully - serviced and ready for work (ex EA). Low hours. Comes with 6 months warranty or 1000hrs (whichever comes first). Delivery available - Only 1 left!

Specification
Head: 47 mtr
Flow: 145 l/sec

SP630.jpg SP631.jpg SP632_1_.jpg SP632_2_.jpg primax.jpg sp632.jpg

Primax CP-150M

Sold

Primax CP-150M coupled to a diesel engine. This fully-automatic, self-priming pump is mounted inside a weatherproof enclosure on a 4-wheeled trailer. Good solids-handling pump (up to 60mm). Ex civil engineering company, used on a 3 year sewer relining project. To be fully-serviced and minor repairs carried out. Sold in good working order.

Primax-Silenced-CP150M-1.jpg Primax-Silenced-CP150M-2.jpg Primax-Silenced-CP150M-3.jpg Primax-Silenced-CP150M-4.jpg Primax-Silenced-CP150M-5.jpg Primax-Silenced-CP150M-6.jpg Primax-Silenced-CP150M-7.jpg

Selwood 3" Pump

Sold

Selwood 3" automatic priming, solids handling pump.
Powered by a Lister TS1 single cylinder, air-cooled, diesel engine. Running at 1500RPM (will rev to 2000). With crank start. All mounted on a 4-wheel chassis with a built in 24 hour capacity fuel tank. This is a very robust contractors pump.

Flow (approx): 250gpm (68m³/hr)
Head: 20 mtrs.

Selwood_Pump(1).jpg Selwood_Pump(2).jpg Selwood_Pump(3).jpg Selwood_Pump(4).jpg Selwood_Pump(5).jpg Selwood_Pump(6).jpg Selwood_Pump(7).jpg

Selwood 80AD

Sold

Selwood 80AD315 auto self-priming pump coupled to a Lister ST1, crank start, 1 cylinder diesel engine. All mounted on a 4 wheeled, site-tow, trailer. With 2 day fuel tank.

3 available

Selwood-80AD-1.jpg Selwood-80AD-2.jpg Selwood-80AD-3.jpg Selwood-80AD-4.jpg Selwood-80AD-5.jpg Selwood-80AD-6.jpg Selwood-80AD-7.jpg Selwood-80AD-9.jpg Selwood-80AD-10.jpg Selwood80AD-1.jpg Selwood80AD-2.jpg

Selwood D100

Sold

Selwood D100 4" automatic, self-priming pump. Powered by a 3 cylinder diesel engine. Mounted in a sound attenuated canopy with forklift pockets. These robust high performance pumps with indefinite dry running ability are particularly suitable for water companies, pump hirers and high flow applications. The range offers easy operation, unparalleled reliability and inherent safety.

Specification
Head: 27m
Flow: 120m³/hr

Selwood-D100-1.jpg Selwood-D100-2.jpg Selwood-D100-3.jpg Selwood-D100-4.jpg Selwood-D100-5.jpg Selwood-D100-6.jpg Selwood-D100-7.jpg Selwood-D100-8-copy.jpg

Selwood 100C

Sold

Selwood 100C - 4" pump powered by a Deutz 10/11, 3 cylinder, electric start, diesel engine. All mounted inside a sound attenuated canopy. Auto priming, robust, simple to use and mounted on a two wheeled, road legal, fast tow trailer - 2061 hours run.

Selwood-100C-1_SP4292.jpg Selwood-100C-2_SP4292.jpg Selwood-100C-3_SP4292.jpg Selwood-100C-4_SP4292.jpg Selwood-100C-5_SP4292.jpg Selwood-100C-6_SP4292.jpg Selwood-100C-7_SP4292.jpg Selwood-100C-8_SP4292.jpg Selwood-100C-9_SP4292.jpg Selwood-100C-10_SP4292.jpg

Selwood D75

Sold

Selwood D75 3" pump which features auto self priming this pump is coupled to a Hatz electric start engine. This combination comes supplied on a 2 wheel towable trolley. As with all of our used pumps this unit comes fully serviced, painted and tested. We have four in stock. Click To View Our Data Sheet for our Selwood D75

1.jpg 2.jpg 3.jpg 5.jpg 6.jpg 7.jpg 8.jpg

Selwood 100C

Sold

Selwood 100C 4" pump.
Ex local authority pump. Low hours. Coupled to a Lister TR3, electric start, diesel engine - Mounted on a road-tow trailer.

Selwood-100C-1.jpg Selwood-100C-2.jpg Selwood-100C-3.jpg Selwood-100C-4.jpg Selwood-100C-5.jpg Selwood-100C-6.jpg

Selwood 150C

Sold

Selwood 150C Pump. YOM 2003. Ex local authority pump. Low hours. Powered by a VM/GM 3 cylinder air cooled electric start, diesel, engine. All mounted on two pneumatic wheels - road legal fast tow trailer. Sold fully serviced in good working order - 3 month warranty. We currently have three Selwood 150C pumps for used sale, These are in varied condition.

SP6350_1_.jpg SP6350_2_.jpg SP6350_3_.jpg SP6350_4_.jpg SP6350_5_.jpg SP6350_6_.jpg SP6350_7_.jpg SP6350_8_.jpg SP6350_9_.jpg

Selwood 150C

Sold

Selwood 150C self-priming pumps fitted with Hatz 4L41C, air-cooled diesel engines coupled with a diaphragm priming set. They are fully automatic mounted on a robust chassis fuel tank with lifting frame at eye lift point. Present painted in original black/yellow and will come fully serviced and tested to be in good working order. Will also be repainted before leaving our depot.We can also supply you with suction and delivery hose/fittings and can sour= ce spare parts for all Selwood units and provide a good pump maintenance and servicing agreements.
Delivery available.

SP6244_1_.jpg SP6244_2_.jpg

Selwood 150C

Sold

Selwood 6" self-primig, solid handling, pump coupled to a 3 cylinder, enclosed, Deutz, silence, diesel engine with electric start. Will handle large solids. The pump is mounted on a two-wheeled, fast-tow, trailer.

This is an ex Anglian Water pump and has very low hours. Yet to be re-painted so can be sprayed in a colour of your choosing.

Sold fully serviced and tested.

Selwood-150C(1).jpg Selwood-150C(2).jpg Selwood-150C(3).jpg Selwood-150C(4).jpg Selwood-150C(5).jpg Selwood-150C(6).jpg

Selwood 100C

Sold

Selwood 100C - 4" pump powered by a Deutz electric start, diesel engine, mounted inside a sound attenuated canopy on a road tow trailer (non-breaked). Auto priming, robust and simple to use - 3490 hrs

selwood-100c-rt-1.jpg

Selwood HSP20 power pack (no water pump included)

Sold

Make an enquiry

SP9125 SP9129 SP9130

Selwood Power pack's in stock (no water pump included). We have 4 available to purchase the Selwood HSP20 which offers Max flow of 30 lt/min, Max Head 190bar Hydraulic pressure and 241bar full relief value. The engines are silent pack Hatz diesel variable speed 2L41C 2 cylinder which are air cooled and silenced, operating on a 12V electric start. The fuel tanks' will hold an approx value of 130ltr 1170mm x 550mm x 180mm. These power pack's are 4 wheel site towable and have a weight of 760kg when dry. These are key start with the starter panel representing oil pressure water and temp. The dimensions of these power packs are length 900mm width 1080mm and height 1630mm (approx). We have a selection of hydraulic submersible pumps available to purchase at very reasonable prices to fit these packs and our expert team will be able to assist. SP9125 Technical Information SP9129 Technical Information SP9130 Technical Information

HSP201.JPG HSP202.JPG HSP203.JPG HSP204.JPG

Selwood 150 SA

Sold

Selwood 150 SA automatic, self-priming pump coupled to a Lister TX3 diesel engine with electric start.The Selwood SA range is a highly robust, compact and particularly suitable for high flow industrial applications.

Specification
Capacity: 390m³/h
Suction Lift: 9.1m
Deliver Head: 40.5m
Solids Size: 45mm
Max pressure: 4.5 Bar @ 2000rpm

Selwood_150SA-1_(SP6406).jpg Selwood_150SA-2_(SP6406).jpg Selwood_150SA-3_(SP6406).jpg Selwood_150SA-4_(SP6406).jpg Selwood_150SA-5_(SP6406).jpg Selwood_150SA-6_(SP6406).jpg Selwood_150SA-1_(SP6405).jpg Selwood_150SA-2_(SP6405).jpg Selwood_150SA-3_(SP6405).jpg Selwood_150SA-4_(SP6405).jpg Selwood_150SA-5_(SP6405).jpg Selwood_150SA-7_(SP6406).jpg Selwood_150SA-8_(SP6406).jpg

Selwood 150C

Sold

Selwood 150C - 6" pump powered by a Deutz electric start, diesel engine, mounted inside a sound attenuated canopy on a road-tow trailer (non-braked). Auto priming, robust and simple to use.

selwood-150c-rt-1.jpg

Selwood / Svedala SH 200

Sold

This is a Selwood manufactured pump using a Volvo TWD1210V 6 cylinder, water-cooled, diesel engine. Coupled to a Metso Svedala 8x6" high head, high chrome pump. Being very suitable for abrasive water and slurries. It will handle solids up to 60mm. The pump is fully automatic, self-priming using the Selwood air pump and separator tank. The above is all mounted on a robust chassis fuel tank with lifting frame. Presently painted in original black / yellow. We are able to offer this pump fully serviced, tested and re-painted - 2 available

Comes with warranty ready for your project!

Specification
Flow: 1040 m³/hr
Head: 85 mtr
Hours: 6331

Selwood-200SH-9.jpg Selwood-200SH-10.jpg Svedala-A4162-1.jpg Svedala-A4162-2.jpg Svedala-A4162-3.jpg Svedala-A4162-4.jpg Svedala-A4162-5.jpg Svedala-A4162-8.jpg Svedala-A4162-9.jpg Svedala-A4162-High-Head-1.jpg Svedala-A4162-High-Head-2.jpg Svedala-A4162-High-Head-3.jpg Svedala-A4162-High-Head-4.jpg Svedala-A4162-High-Head-5.jpg Svedala-A4162-High-Head-6.jpg Svedala-A4162-High-Head-7.jpg Svedala-A4162-High-Head-9.jpg Svedala-A4162-High-Head-10.jpg

Selwood 150C

Sold

Selwood 150C self-priming pump powered by a VM/GM 3 cylinder air cooled electric start, diesel, engine. All mounted on two pneumatic wheels - road legal fast tow trailer. Sold fully serviced in good working order.

Selwood-S150-1.jpg Selwood-S150-2.jpg Selwood-S150-3.jpg Selwood-S150-4.jpg Selwood-S150-5.jpg Selwood-S150-6.jpg Selwood-S150-7.jpg

Selwood 150SA

Sold

Selwood 150SA high performance centrifugal pump with auto-priming from a seperate water tolerant reciprocating air pump.

Oil immersed mechanical shaft seal allows for extended dry running.

This pump is ex water company.

Max Head: 40.5 mtrs
Max Flows: 450m³/hr
Max Solids: 45mm

selwood-sa150-1.jpg selwood-sa150-2.jpg selwood-sa150-3.jpg selwood-sa150-4.jpg selwood-sa150-5.jpg selwood-sa150-6.jpg selwood-sa150-7.jpg selwood-sa150-8.jpg

Clarke IK6HUF60 Fire Pump Engine

Sold

This Clarke IK6HUF60 Fire Pump Engine. This engine is rated from 170 - 175 BHP and 2600 - 2800 RPM.

This engine can be coupled with many fire pumps including SPP and Armstrong.

Manufactured: 11/2002
Hours: 64

clarke-fire-pump-engine-1.jpg clarke-fire-pump-engine-2.jpg clarke-fire-pump-engine-3.jpg clarke-fire-pump-engine-4.jpg clarke-fire-pump-engine-5.jpg clarke-fire-pump-engine-6.jpg clarke-fire-pump-engine-7.jpg clarke-fire-pump-engine-8.jpg clarke-fire-pump-engine-9.jpg clarke-fire-pump-engine-10.jpg clarke-fire-pump-engine-11.jpg

Hamworthy Bareshaft Fire Pump

Sold

Hamworthy bareshaft, side-suction, fire pump. This was previously used as a standby oil installation pump. 8" x 8" flanges fitted with a packed gland seal. The flanges are horizontal each side. Complete with bearing pedestal. The pump was coupled to a Volvo TD60 diesel engine (76kW @ 1500rpm / 100kW @ 1800rpm). Pictures to follow.

Max Flow: 400m³HR
Max Head: 115mtrs

Duty Points
400m³HR @ 63mtrs
300m³HR @ 75mtrs
200m³HR @ 95mtrs

Hamworthy-End-Suction-Pump-1.jpg Hamworthy-End-Suction-Pump-2.jpg Hamworthy-End-Suction-Pump-3.jpg Hamworthy-End-Suction-Pump-4.jpg Hamworthy-End-Suction-Pump-5.jpg Hamworthy-End-Suction-Pump-6.jpg

SPP KP10X

Sold

SPP KP10X 5x4" Fire Drive Pump.
These make great irrigation pumps and are powered by a 6 cylinder, naturally aspirated, Iveco diesel engine.
Engine has been re-worked by Firedrive LTD to meet certification. The engine is fitted with 2 sets of lead acid batteries and two AC chargers.
A silencer and flexible bellows are included.
Wiring manual also provided.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Specification
Impeller Dia. - 246mm
3604LPM @ 7.77 BAR pressure (this can be reduced to meet next application).
Y.O.M: 1999
Hours: 36

Sold fully inspected and serviced.

Installation available.

SP8095_10_.jpg SP8095_1_.jpg SP8095_2_.jpg SP8095_3_.jpg SP8095_4_.jpg SP8095_5_.jpg SP8095_6_.jpg SP8095_7_.jpg SP8095_8_.jpg SP8095_9_.jpg

SPP KP12X

Sold

SPP KP12X fire pump.

Pump comes fitted with automatic fire control panel which automatically manages operation of the pump in the event of a fire.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Flow: 98 l/sec
Head: 75.38 mtrs
Speed: 2766 rpm
Hours: 375
Manufactured: 1995

spp-kp12x-sp9099-1.jpg spp-kp12x-sp9099-2.jpg spp-kp12x-sp9099-3.jpg spp-kp12x-sp9099-4.jpg spp-kp12x-sp9099-5.jpg spp-kp12x-sp9099-6.jpg spp-kp12x-sp9099-7.jpg

SPP TD20E

Sold

SPP TD20E split-casing, FM Approved, fire pump. This pump is powered by an Iveco, 6 cylinder, turbo-charged, fire-drive engine. Fitted with new twin starter battery, battery charger, control panel and sealed header tank intercooler. Sold fully-serviced & tested. Installation available.

Comes with 3 months warranty (subject to satisfactory installation).

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Specification
Rated Capacity: 2,000 US gpm
Rated Net Pressure: 125 psi
Net Pressure @ 150% capacity: 103.20
Impeller Diameter: 12.4"

spp-td20e-sp9053-1.jpg spp-td20e-sp9053-2.jpg spp-td20e-sp9053-3.jpg spp-td20e-sp9053-4.jpg spp-td20e-sp9053-5.jpg spp-td20e-sp9053-6.jpg spp-td20e-sp9053-7.jpg spp-td20e-sp9053-8.jpg spp-td20e-sp9053-9.jpg spp-td20e-sp9053-10.jpg

SPP TD20E

Sold

SPP TD20E pump coupled to a coupled to a Firedriver FM 275 6 cylinder diesel engine.

New automatic control panel to be fitted (see pictures).

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Flow: 2000 US GPM (7560 L/MIN)
Pressure: 125 PSI
Speed: 2775 RPM
Impeller Dia: 12.40"

spp-td20e-sp9086-1.jpg spp-td20e-sp9086-2.jpg spp-td20e-sp9086-3.jpg spp-td20e-sp9086-4.jpg spp-td20e-sp9086-5.jpg spp-td20e-sp9086-6.jpg spp-td20e-sp9086-7.jpg spp-td20e-sp9086-8.jpg spp-td20e-sp9086-9.jpg spp-td20e-sp9086-10.jpg

SPP TD20E

Sold

SPP TD20E fire pump coupled to a Caterpillar 3208 diesel engine.

This pump comes fitted with a fire control panel for fully automatic control. Comes complete with 4 lead acid batteries and free standing 8 hour fuel tank.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Flow: 2000 US GPM
Head: 125 psi
Impeller Dia: 301.2 mm
Hours: 134
Manufactured: 2001

sp9096-spp-td20e-1.jpg sp9096-spp-td20e-2.jpg sp9096-spp-td20e-3.jpg sp9096-spp-td20e-4.jpg sp9096-spp-td20e-5.jpg sp9096-spp-td20e-6.jpg sp9096-spp-td20e-7.jpg sp9096-spp-td20e-8.jpg sp9096-spp-td20e-9.jpg

SPP TD20D - EM

Sold

SPP TD20D fire pump driven by a Brook CF280MN 185kW, 415V, 50Hz, 2950 rpm electric motor.

SPP Pumps have been manufacturing fire pumps for over 100 years and has one of the widest ranges of approvals of any manufacturer in the world.

SPP fire pumps are designed specifically for the very particular needs of fire protection and are approved by most of the major fire protection bodies around the world.

Flow: 8400 l/min
Pressure: 9 bar
Impeller Dia: 282mm
Year of Manufacture: 2000

sp9106-spp-td20d-1.jpg sp9106-spp-td20d-2.jpg sp9106-spp-td20d-3.jpg sp9106-spp-td20d-4.jpg sp9106-spp-td20d-5.jpg sp9106-spp-td20d-6.jpg

SPP HH150

Sold

SPP 150 High Head Pump powered by the industrial standard Lister CDT6,
water-cooled, turbo charged engine. This pump is made for the mines and
quarry industry, as it is hard wearing and has good solids handling for its head of 45mm.
Rapid priming using a 60CFM oil lubricator vacuum pump.
Flow upto 550m³HR and head up to 105mtrs @ 2100RPM
Has an 8" (200mm) suction and 6" (150mm) outlet.
Skid base fuel tank offering 270ltrs or 12 hours full load run time.
Fuel pipes are suitable for a bulk tank connection.
The exhaust is 85dba @ 1mtr and coupled with a spark arrestor.

IMGP7755.JPG IMGP7756.JPG IMGP7757.JPG IMGP7758.JPG IMGP7759.JPG IMGP9086.JPG

Sykes UVC3

Sold

Sykes UVC3 high capacity general purpose pump, used for pumping wastewater, oily water, sewage, sludge and wellpoint dewatering. Automatic priming and repriming with high flow rate vacuum pump.

Fitted with 3 phase, 4kW electric motor and mounted on a skid base with fork lift pockets.

Comes complete with bauer couplings

Max Flow: 45m³/hr
Max Head: 15m
Speed: 1435 rpm
Inlet/Outlet: 3"/80mm

sykes-uvc3-1.jpg sykes-uvc3-2.jpg

Sykes / SPP GP100M

Sold

SPP / Sykes GP100M 4" pump coupled to a Lister Petter TS2 diesel engine with electric start. The pump has recently been fully refurbished and serviced by Stuart Pumps Ltd. It is an automatic, self priming pump and is mounted on a 4 - wheeled chassis with a 24 hour fuel tank.

GP100-SP4259-1.jpg GP100-SP4259-2.jpg GP100-SP4259-3.jpg GP100-SP4259-4.jpg GP100-SP4259-5.jpg GP100-SP4259-6.jpg

SPP Autoprime AC50

Sold

Autoprime AC50 with max flow of 37m3/h and max head of 28m. The suction size is 50mm/2". Powered by a Lister-Petter AD1 on a 12v battary, this engine is air cooled. 14 litre chassis fuel tank / open skid. manufactured in 2000 this pump comes fully serviced and repainted if required.

1.jpg 2.jpg 3.jpg 4.jpg 5.jpg

Sykes / SPP GP100M

Sold

Sykes / SPP GP100M pump being an automatic, solids handling, self - priming pumpset. The pump is coupled to a Lister TR2, air - cooled, electric start, diesel engine on a skid base with 24 hour fuel tank.Delivery available.

IMGP7774.JPG IMGP7775.JPG IMGP7776.JPG IMGP7777.JPG IMGP7778.JPG IMGP7779.JPG IMGP7780.JPG

Sykes / SPP GP100M

Sold

Sykes / SPP GP100M pumpset being an automatic, self - priming, contractors, solids - handling pump. The pump is coupled to a totally enclosed, fan-cooled (TEFC), electric motor of 11kW / 415V / 50Hz / 3 - phase, running @ 1450RPM. Complete with a IP56 direct on line starter box. The pumpset is mounted on a 4 - wheeled chassis with tow bar.
Also offered on a skid-base.
Delivery available.

SP4173(4).jpg SP4173_1_.jpg SP4173_2_.jpg SP4173_3_.jpg

Sykes / Primax Yakka 150

Sold

Sykes Pumps / Primax Pumps, Yakka 150 6" automatic priming contractors pump set coupled to a Perkins 404 water cooled diesel engine.

Will pump quarry water for sewage overpumping with a rapid reprime. Will pump clean water or waste water including sewage and trade waste. This is a fully automatic, self-priming pump which can handle solids up to 77mm.

The pump is mounted on a high speed road tow trailer and is housed inside a sound attenuated weatherproof enclosure.

Nearly new condition.

Specification
Flow: 1300 gpm
Impeller Dia: 275 mm
Y.O.M: 2010
Hours: 1479

sykes-yakka-150-1.jpg sykes-yakka-150-2.jpg sykes-yakka-150-3.jpg sykes-yakka-150-4.jpg sykes-yakka-150-5.jpg sykes-yakka-150-6.jpg sykes-yakka-150-7.jpg sykes-yakka-150-8.jpg sykes-yakka-150-9.jpg

Sykes / SPP GP150M

Sold

Sykes / SPP GP150M pumpset. The pump is an automatic, self - priming pump, coupled to Lister TR3, electric start, diesel engine. Mounted on a two-wheeled, high speed trailer. Ex water company. Comes with 6 months warranty.

Sykes_GP150M_TR3(3).jpg Sykes_GP150M_TR3(4).jpg Sykes_GP150M_TR3(5).jpg Sykes_GP150M_TR3(6).jpg Sykes_GP150M_TR3(7).jpg Sykes_GP150M_TR3(8).jpg

Sykes GP200M

Sold

Sykes GP200M automatic, self-priming pump.
Being a 3 blade, solids handling pump.
Coupled to a Lister, water-cooled, CD4 diesel engine.
The pump is mounted on a 16 hour fuel tank chassis and is fitted with
bauer couplings.
It will pump 1450gpm (400m³HR) at upto 57 mtr head.
Suited for all civil engineering, quarry and wellpoint dutys.

IMGP7743.JPG IMGP7744.JPG IMGP7746.JPG IMGP7750.JPG IMGP7751.JPG

Sykes GP300

Sold

Sykes GP300 powered by a Volvo TD61A Water Cooled Turbo Charged Engine, Med. Hours in Good Working Condition 3,500gpm. Heads up to 35 metres - clean water. Fully Self Priming, ideal Quarry or River Pump Similar stock will be available soon.

SP319.jpg

Sykes UVC4

Sold

Sykes UVC4 Pump powered by a Lister HR2, air-cooled, diesel engine.
Mounted on a 4-wheeled, 24 hour capacity fuel tank chassis with lifting frame.

This pump will self prime to 20ft. May be old but is British made and will pump many more millions of gallons. Ideal site drainage pump. Will pump clean water, sewage or trade effluents.

Sold with 1 months warranty.

Flow upto 475gpm @ 1500rpm - 68ft Head

Univac_UVC4(1).jpg Univac_UVC4(2).jpg Univac_UVC4(3).jpg Univac_UVC4(5).jpg Univac_UVC4(6).jpg Univac_UVC4(7).jpg Univac_UVC4(8).jpg Univac_UVC4(9).jpg

Tsurumi KRS2-150

Sold

This pump was bought in error and has only been used 1 day for demonstration purposes. Total running time is less than 6 hours. Repainted, product like new.

The KTV2 and KRS2 series pumps have a similar construction to the KTV and KRS drainage pumps respectively; however for increased wear resistance their impellers are in chromium iron. The KTV2 and KRS2 pumps have a built in agitator, also in chromium iron, to stir sand and silt into suspension for pumping. Similarly they have double mechanical seals (inboard: silicon carbide-silicon carbide). To improve wear resistance still further, the KRS2 models also feature 4 pole motors.

Supplied with 20 metres of TRS power cable, for quarry and mining applications. KTV2 models are supplied with a threaded outlet and a hose connector.

Specification
Head: 22 m/second
Flow: 3,100 l/minute
Outlet: 150mm (BSPM/Flange)
Power: 9kW
Cable: 20 meters TRS cable

Tsurumi-KRS2-150-1.jpg Tsurumi-KRS2-150-2.jpg Tsurumi-KRS2-150-3.jpg Tsurumi-KRS2-150-4.jpg Tsurumi-KRS2-150-5.jpg

Warman 12/10 M

Sold

12/10M Warman sand and slurry pump coupled to a 45kW 400V VEM electric motor. 1470RPM.

This pump has very low running hours as it was originally purchased by mistake.

Condition as new. Comese with 6 months warranty.

Warman_1_.jpg Warman_3_.jpg

Warman 10/8 - Type S Solutions

Sold

Warman Cast Iron 10 / 8 Type S Solutions.

This pump is new. It is "old stock" which has never been used.

This pump is from Warman, the hard iron pump company. This is a solutions grade pump made in cast iron. Fitted with a shrouded 8 vane impeller. The suction is 12" and the outlet is 10" flanged.

Suitable for all clean water applications.

Shaft seal is multi ring packed gland.

Bearing pedestal is Frame E.

Pump7_1_.jpg Pump7_2_.jpg Pump7_3_.jpg IMGP2041.JPG Warman-10-8.jpg

Warman 4 x 3 HH

Sold

Size 4 x 3 HH Warman Pump. S/No RO30865. Warman pumps are ideal for pumping sand, gravel and other abrasive materials.

Pump8_1_.jpg Pump8_2_.jpg Pump8_3_.jpg

Warman 6 x 4 DAH

Sold

Warman 6 x 4 DAH Mill Scale Slurry Pump coupled to a Bam or Weg 30kW Electric Motor, manufactured 2011.

Specification:
Flow: 320 m³/min
Head: 14.4 mtr
Speed: 938 rpm
Pressure: 3.5 bar
Inlet: 6"
Outlet: 4"

warman-6x4-ah-1.jpg warman-6x4-ah-2.jpg warman-6x4-ah-3.jpg warman-6x4-ah-4.jpg warman-6x4-ah-5.jpg warman-6x4-ah-6.jpg warman-6x4-ah-7.jpg warman-6x4-ah-8.jpg

Warman 3 x 2 Type SC Rubber Lined

Sold

Warman 3 x 2 Type SC Rubber Lined S/No WP16858. Age unknown. Has been in stock 5/6 years since recondition. This item is in good condtion.

SP7085_1_.jpg SP7085_2_.jpg

Hard Iron Warman Type Pump

Sold

An example of a hard iron Warman Type Pump coupled to a Perkins 1103 engine on a skid base. Built for a client to boost his quarry sand waste line.
Installation available

Warman1103_1_.jpg Warman1103_2_.jpg

Weir Split Pumps

Sold

Make an enquiry

SP8042, SP8043

Weir Split Casing Pumps SDA 600/800. New and Unused, 2 Available in stock, No sensible offer refused.

Specification
Flow: 28,000gpm
Head 238 FT

Weir_1_.jpg Weir_2_.jpg Weir_3_.jpg Weir_4_.jpg Weir_5_.jpg Weir_6_.jpg Weir_7_.jpg Weir_8_.jpg IMGP8129.JPG IMGP8130.JPG IMGP8131.JPG

Wright Rain Irrigation Pump

Sold

This is a Wright Rain Irrigation Pump 4 x 3", 4 cylinder industrial Ford diesel engine. Mounted on a 12 hour capacity fuel tank.
The pump is a clean water type and is manual primed with an air pump. 4" Bauer inlet and 3" flanged outlet. Will run 1 rain gun with ease. Sold in good working order, open to testing - no warranty supplied given the price.

Flow: 670gpm / 130m³/hr with pressure of 100mtrs / 10 Bar / 145PSI.

Soon to be available!
This pump with an Isuzu 3LD engine offering lesser head @ £3,000...info to follow.

Comes with 30 day warranty.

Wright_Irrigation-1.jpg Wright_Irrigation-2.jpg Wright_Irrigation-3.jpg Wright_Irrigation-4.jpg Wright_Irrigation-5.jpg Wright_Irrigation-6.jpg Wright_Irrigation-7.jpg Wright_Irrigation-8.jpg Wright_Irrigation-9.jpg

Wilden M8/T8

Sold

The Wilden M8/T8 2" diaphragm pump is an air-operated, positive displacement, self-priming pump.

Double diaphragm pumps are suitable for pumping water, slurry, sewage, oils, resins, chemicals and more. Can be used for dewatering operations, filling/emptying liquids from tanks/containers and can be used for pumping abrasives or solids.

Read the Wilden M8/T8 manual

Flow: 590.5 l/min
Head: 275 feet
Pressure: 8.6 bar
Max Solids: 1/4" (6mm)

wilden-m8-1.jpg wilden-m8-2.jpg wilden-m8-3.jpg

Ebara 3LS 40-125/2.2

Sold

Ebara 3LS 40-125/2.2 pump. This pump is produced of aluminium and cast iron, it has a mechanical seal with stationary ring secured against rotation. The pump is a flanged DN50 model with precision casting impeller EN 1.440P it is three phase and runs at 2900 RPM. 50HZ it is IP55 rated.

Please click here to view a Brochure for this pump series

Please click here to view a DataSheet for this pump

1.jpg 2.jpg

Ebara MD 32-160 2.2

Sold

Ebara MD 32-160/2.2. This Ebara is in near new condition it offers max heads of 35.5m, this pump operates at 220-240V it is 2.2KW, 50HZ and 3HP with an IP55 rating. This pump can handel liquids pumping to a temperature of 90"c. The pump is sold in great condition with viewing welcome

Please click here to view a DataSheet for this pump

1.jpg 2.jpg

Nocchi MXC 200/52

Sold

In new and unused condition, Nocchi MCX 200/52 pump. This is an Italian made Nocchi pompe pump, it will offer Max head at 62m. This pump is 50HZ and 1.3KW, its' Max horse power is 2.5 although dependable or usual running is 1.8 HP. This pump comes with an IP rating of IP44 and is thermally protected with continuous duty

1.jpg 2.jpg

Haskel Air Driven Test Pump

Sold

Haskel Air Driven Test Pump, Air driven piston type water pump, water pressure testing to about 2,000 psi, upto 100 psi air pressure on inlet, light and portable in GWO.

SP214.jpg
A Note from our MD. : The above descriptions are provided in good faith, we do our best to offer factual information on all used equipment. “we as a result of selling two used generators, we had provided incorrect operational hours, which had been relayed onto a customer by mistake". We do our best to offer factual information however we take no responsibility for any or all information provided written or aural. Having stated the forgoing we undertake to provide a quality service with every sale. We limit our liability to repair - replacement and transport costs. (for the record we paid tens of thousands to a company as we standby our values, by negotiation. Not legal).
Go Top